Samsung WF218ANS/XAC Washer Leaking: Safe Checks and Compatible Seal Parts

A leaking Samsung WF218ANS/XAC front-load washer should not be diagnosed by part name alone. The safest first step is to stop the cycle and locate the water source. If water is near electrical connections, unplug the washer only when it is safe to do so, and shut off the water-supply valves. Do not reach into standing water or remove panels unless you are qualified to work on the appliance.

Check the model label on the washer and compare the replacement part number before ordering. The verified XPart Supply model hub for this appliance is the Samsung WF218ANS/XAC washer parts hub. It identifies three verified buyable components associated with the leaking issue: the DC62-00223A Washer Oil Seal, DC64-00802A Washer Door Boot / Door Diaphragm, and DC69-00804A Washer Outer Tub Gasket.

What should you do first if the Samsung WF218ANS/XAC is leaking?

Stop the washer and note whether the leak continues after the cycle ends. Keep children and pets away from the water. If the water is close to the power cord, outlet, or other electrical connections, disconnect power only if you can do so without stepping into water or touching unsafe equipment. Close the hot- and cold-water supply valves.

Before moving the washer, look for the first visible point where water appears. Water can travel across the floor or cabinet, so the wettest area is not always the failed component. Use a towel to help trace the source after the appliance is safe and no longer operating.

Where is the leak coming from?

The leak location and cycle stage can narrow the inspection:

• Front door area: Inspect the door boot for tears, distortion, trapped debris, or an item caught between the boot and door glass. A small amount of water left on the door after opening may not indicate the same problem as water escaping while the door is closed.
• Underneath or near the tub: The oil seal or outer tub gasket may be relevant, but hoses, the drain system, and other internal areas can also send water toward the bottom of the cabinet.
• Rear of the washer: Check the water-supply hose connections and drain hose for looseness, damage, or movement. Turn off the supply before handling hose connections.
• Detergent drawer: Buildup, excess detergent, or excessive suds can cause water or suds to overflow from the dispenser area. Clean only accessible areas according to safe appliance-care practices.
• During draining: Inspect the accessible drain hose and, where provided and safe to access, the drain filter area for an obstruction. Do not open a filter if the washer may contain hot water or if doing so would expose you to uncontrolled water.

Could more than one component cause the leak?

Yes. A leaking Samsung WF218ANS/XAC washer may have more than one contributing issue. For example, a damaged door boot can allow water out of the front while a restricted drainage area creates additional water movement during draining. A loose hose connection can leak at the rear even when the door seal looks normal. Detergent buildup or excessive sudsing may also create overflow that resembles a seal failure.

For that reason, do not assume that replacing one seal will resolve every leak. Inspect the visible hoses, door area, dispenser, and accessible drainage points first. If the source is hidden, the leak continues, or the cabinet, tub, or internal pump area appears damaged, stop using the washer and arrange qualified service.

When is the DC64-00802A Washer Door Boot / Door Diaphragm relevant?

The DC64-00802A Washer Door Boot / Door Diaphragm is the verified XPart Supply door-area component for the Samsung WF218ANS/XAC leaking issue. It is worth checking when water escapes from the front door while the door is closed, or when the boot shows a tear, split, deformation, or debris that prevents a proper seal.

Inspect the boot carefully with the washer powered down. Do not use sharp tools that could puncture the rubber. Confirm that the part number on the replacement matches DC64-00802A and that the model label reads Samsung WF218ANS/XAC before ordering.

When might the DC62-00223A Washer Oil Seal be involved?

The DC62-00223A Washer Oil Seal is a verified seal component for the Samsung WF218ANS/XAC hub. It may be considered when the leak appears to originate from an internal tub or rotating-area seal rather than from the door boot, dispenser, or an external hose connection. The location of the water alone does not prove that this seal has failed, because water can travel inside the cabinet.

Internal seal work may require substantial disassembly and should be undertaken only by someone with the appropriate appliance-repair skill. If you cannot clearly identify the source, qualified service is the safer option. Confirm the exact part number, DC62-00223A, against the model label before purchasing.

When might the DC69-00804A Washer Outer Tub Gasket be involved?

The DC69-00804A Washer Outer Tub Gasket is another verified XPart Supply component for the Samsung WF218ANS/XAC leaking issue. It may be relevant when inspection points toward the outer tub area rather than the door opening or external hoses. A gasket concern should not be assumed from a puddle underneath the washer, since several drainage and hose-related issues can produce the same symptom.

Because access to an outer tub gasket can involve internal cabinet work, disconnect power and water before any qualified inspection. Confirm both the appliance model and the part number DC69-00804A before ordering.

Which verified parts fit the Samsung WF218ANS/XAC?

XPart Supply’s verified model hub lists these buyable parts for the leaking Samsung WF218ANS/XAC washer:

• DC64-00802A — Washer Door Boot / Door Diaphragm, for inspection of the front door sealing area.
• DC62-00223A — Washer Oil Seal, for an internal seal concern identified during diagnosis.
• DC69-00804A — Washer Outer Tub Gasket, for an outer-tub gasket concern identified during diagnosis.

These parts are listed as verified for the Samsung WF218ANS/XAC model hub, but the model label and replacement part number should still be checked before ordering. A verified fitment does not identify which component has failed or guarantee a repair outcome.

Should you run the washer again after finding water?

Do not run another cycle simply to reproduce the leak if water is near electrical connections, the leak is substantial, or the source is not clear. If the leak persists, appears to come from an internal area, or involves a damaged tub or pump area, leave the washer disconnected and request qualified service. Recheck the model label and part number before selecting a replacement component.

Frequently asked questions about a leaking Samsung WF218ANS/XAC washer

Is a small drip from the door always a failed door boot?

No. A small amount of water remaining on the door after opening can differ from water escaping while the door is closed. Inspect the boot for damage and check for debris before concluding that the DC64-00802A is needed.

Can a drain hose or filter cause the same symptom as a bad seal?

Yes. A hose, filter, pump area, or obstruction may leak or overflow during draining and make water appear beneath the washer. Check only accessible areas safely.

Should I replace all three verified parts?

Not automatically. Multiple components can create similar symptoms, but replacing parts without locating the source can add unnecessary work. Diagnose the leak location and cycle stage first.

What should I confirm before ordering?

Confirm that the appliance is a Samsung WF218ANS/XAC washer, verify the model label, and match the requested part number: DC62-00223A, DC64-00802A, or DC69-00804A.