Washer Vibrating or Off-Balance? Hanger Spring 34001274 – Fix Excessive Shaking Fast
If your top-load washer is shaking violently, walking across the floor, or making loud banging noises during the spin cycle, a failed hanger spring is the most common cause. In most Whirlpool and Maytag top-load washers, the tub is suspended by four hanger springs that absorb movement during agitation and spin. When one or more springs break or lose tension, the tub swings freely and slams against the cabinet. ⚡ Common failure point in Whirlpool-platform top-load washers. Part 34001274 is the genuine OEM replacement set of 2 springs that restores proper tub suspension and eliminates abnormal vibration immediately.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ Washer powers on and runs through cycles normally
- ✔ Agitation and water fill functions work correctly
- ✔ Water supply and drain hoses are confirmed OK
- ✔ Lid switch and door latch engage properly
- ✔ ONLY problem is excessive vibration, banging, or tub movement during spin
Not sure? Send us your model number — we'll confirm before you order.
🔧 Common Symptoms
- Washer shaking violently or walking across the floor during spin — most common complaint
- Loud banging or thumping noise during spin cycle
- Tub visibly off-centre or hitting the cabinet walls
- Washer stops mid-cycle due to out-of-balance detection
- Visible broken or detached spring inside the cabinet
- Increased vibration that has worsened progressively over time
✔ If these symptoms match, a failed hanger spring is the most likely cause in this platform.
✔ In most cases, replacing the full set of 2 springs restores normal, quiet operation immediately.
📦 Part Details
- Part Number: 34001274
- Type: Tub suspension hanger spring — set of 2
- Replaces: OEM direct-fit hanger spring assembly — supersedes 34001274 (no modification required)
- Brands: Whirlpool, Maytag, Amana, Crosley
While the cabinet is open, inspect all four hanger springs — they wear at the same rate, and replacing only the broken one often leads to a repeat failure within months. Replacing the full set ensures balanced suspension and saves a second service call.
⚙️ Installation
Skill Level: Easy — 20–30 minutes. Unplug the washer before beginning. Remove the cabinet top or front panel to access the tub suspension points, unhook the old springs from the tub ring and cabinet tabs, and snap the new springs into place. No tools required for the spring swap itself — a putty knife or panel clip tool may be needed to release the cabinet.
✓ Compatible Models
Confirmed compatible with WTW4800XQ2, WTW4800XQ4, WTW4850XQ0, WTW4850XQ2, WTW5000DW0, WTW5000DW1, WTW5000DW2, WTW5000DW3, MVWC400XW4, MVWC415EW0, MVWC415EW1, MVWC425BW0, MVWC425BW1, MVWX655DW0, MVWX655DW1, plus additional Whirlpool-platform models. Contact us to verify your model number before ordering.
💡 Pro Tip
Top-load washers use four hanger springs, and this listing covers two. If your machine has been in service for several years, the remaining springs are likely fatigued even if they haven't snapped yet. Order two sets (4 springs total) and replace them all in one shot — the labour is identical and you'll avoid a repeat repair within the year.
✓ Model-Specific Repair Pages
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Kitchener, Ontario N2E 1W8
- Choosing a selection results in a full page refresh.
