LG Dryer Not Heating, Not Spinning or Making Noise? DC Blower Motor 4681EL1008A — Fix Drum and Airflow Failures Fast
When an LG dryer stops tumbling, loses heat, or starts making a loud grinding or humming noise, the DC blower motor and pulley assembly is the most common root cause. In most LG electric and gas dryers, this motor drives both the drum rotation and the blower fan simultaneously — a single unit responsible for airflow and tumbling. When it fails, the drum stops turning, hot air cannot circulate, and clothes come out wet or the dryer shuts down on thermal overload. ⚡ Common failure point in LG-built dryers across DLE, DLG, and DLEX series. Part 4681EL1008A is the genuine OEM replacement that restores full drum drive and blower function with a direct factory-fit installation.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ Your LG or Kenmore dryer powers on but the drum is not turning or airflow is absent
- ✔ The dryer belt has been confirmed intact — a broken belt is a separate repair
- ✔ Power supply and thermal fuse have been confirmed good
- ✔ ONLY problem is drum not spinning, no airflow, or loud motor noise — not a heating element or gas valve failure
Not sure? Send us your model number — we’ll confirm before you order.
🔧 Common Symptoms
- Dryer drum not turning — motor hums but drum is stationary
- No airflow through the dryer — clothes remain wet after full cycle
- Loud grinding, squealing, or humming noise during operation
- Dryer starts then stops mid-cycle due to thermal overload from blocked airflow
- Burning smell from motor area during operation
- Dryer runs but produces no heat due to failed blower circulation
✔ If these symptoms match, this is the most likely failed component in the system.
✔ In most cases, replacing this motor assembly restores full drum and airflow operation immediately.
📦 Part Details
- Part Number: 4681EL1008A
- Type: DC Drum Drive and Blower Motor with Pulley Assembly — combined unit driving drum rotation and air circulation
- Replaces: 4681EL1002A, 4681EL1002B, 4681EL1008B, 4681EL1008H, 4681EL1008S — no modification required
- Brands: LG, Kenmore
- Weight: 25 lbs — substantial assembly, handle with care during installation
While the dryer is disassembled to access the motor, inspect the drum belt and idler pulley for wear. A worn belt or seized idler pulley puts excessive load on the new motor and will cause premature failure. Replacing all three components at the same time — motor, belt, and idler — is the industry-standard repair and eliminates the need for a second teardown.
⚙️ Installation
Skill Level: Moderate to Advanced — 60 to 90 minutes. Disconnect power before servicing. Remove the dryer front panel and drum to access the motor assembly at the rear of the cabinet. Disconnect the motor wiring harness and blower housing, remove the old motor, and install the new assembly in the same orientation. Reinstall the drum belt around the drum and idler pulley before reassembling the cabinet. Run a full cycle to confirm drum rotation and airflow before returning the unit to service.
✓ Compatible Models
Confirmed compatible with DLE2514W, DLE3733W, DLE5955W, DLG3744W, DLG5966W, DLEX7177WM, DLEX8377WM, DLG9588WM, DLGX3002W, DLGX5102W plus 90+ additional LG and Kenmore dryer models. Contact us to verify your model number before ordering.
💡 Pro Tip
After installing the new motor and reconnecting the wiring harness, run a brief test cycle before reinstalling the front panel and drum. This lets you confirm the motor spins freely, the blower moves air, and there are no unusual noises — without having to disassemble the entire cabinet again if a connector was missed. A 30-second test run saves a potential hour of rework.
✓ Model-Specific Repair Pages
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Kitchener, Ontario N2E 1W8
- Choosing a selection results in a full page refresh.
