WATER LEAKING DURING FILL OR AGITATION
Maytag (Whirlpool Corporation) Washer Mounting Stem-Tub Seal Kit 6-2095720, Fixes Water leaking during fill or agitation
Genuine OEM washer mounting stem and tub seal repair kit. Includes a hub assembly, seal, and spanner nut; it holds the wash tub on the transmission shaft and helps prevent leakage between the tub and shaft.
Part 6-2095720Replaces 2-11148, 2-11457, 2-1537, 2-2521, 2-4012, 201537, 202521, 204012, 22001556, 22001648, 22204012, J28-621, LP340Maytag (Whirlpool Corporation)
Guaranteed to Fit — or your money back.
Confirm your full appliance model number before ordering.
Confirm your full appliance model number before ordering.
Is This the Right Part?
Part Number6-2095720
Replaces2-11148, 2-11457, 2-1537, 2-2521, 2-4012, 201537, 202521, 204012, 22001556, 22001648, 22204012, J28-621, LP340
ManufacturerMaytag (Whirlpool Corporation)
Appliance TypeWasher
Part TypeMounting Stem-Tub Seal Kit
✅ Cross Reference Information
Current Part Number6-2095720
Replaces2-11148, 2-11457, 2-1537, 2-2521, 2-4012, 201537, 202521, 204012, 211148, 211457, 22001556, 22001648, 22204012, J28-621, LP340
Common Symptoms
- Leakage from the tub or transmission-shaft area
- Unusual bearing or tub noise after seal leakage allows water intrusion
- Agitation problems when the mounting-stem assembly is damaged or unstable
Check Before Replacing
- Unplug the washer and shut off its water supply before inspection.
- Look for water underneath the washer or around the tub/transmission-shaft area, especially when the tub is filled or agitating.
- Inspect the mounting-stem and tub-seal area for corrosion, worn sealing surfaces, or visible water tracks after the tub assembly is accessible.
- Check for related tub-bearing damage if leakage has been present for an extended period; do not assume the mounting-stem kit is the sole cause.
Pro Tip
Because leakage can damage the tub bearing, inspect the related bearing and shaft surfaces whenever this seal kit is replaced.
Part Details
Part Number6-2095720
Part TypeMounting Stem-Tub Seal Kit
ManufacturerMaytag (Whirlpool Corporation)
Appliance TypeWasher
Primary FunctionSecures the washer’s inner tub to the transmission shaft and seals the tub-to-shaft interface to help prevent water leakage.
Installation Notes
- Disconnect electrical power and shut off the water supply before beginning service.
- Installation requires access to the washer tub and mounting-stem assembly; follow the model-specific service or installation instructions.
- Inspect and clean the mating shaft and seal surfaces before reassembly, replacing damaged related components as required.
- After reassembly, verify that the tub rotates freely and check for leaks during a controlled test.
Verified Compatible Models
A490, A500, A500S, A502, A502S, A503, A506, A510, A510S, A511, A511S, A512, A512S, A590, A606, A606S, A608, A608S, A610, A612, A612S, A613, A700, A700S, A702, A702S, A710, A4910, A5000, A5910, A6910, ESE9900, ESG9900, LSE1000, LSE7800, LSE7800ACE, LSE7800ACL, LSE7800ACW, LSE7800ADE, LSE7800ADL, LSE7800ADW, LSE7800AEE, LSE7800AEL, LSE7800AEW, LSE7800AGE, LSE7800AGL, LSE7804ACE, LSE7804ACL, LSE7804ACM, LSE7804ADE
Fitment reminder: Match the complete appliance model number, including suffix or revision where applicable, before ordering.
Buy Online Pick Up In-Store
Address
101 Trillium Dr
Kitchener, Ontario N2E 1W8
Kitchener, Ontario N2E 1W8
Phone
Hours
Mon–Fri 9 AM–5 PM • Sat 9 AM–1 PM
