Washer Vibrating Excessively or Walking Across the Floor? Balance Weight MAG62583007 – Fix Drum Imbalance Fast
Excessive vibration, loud thumping, and a washer that moves across the floor during spin cycles are classic signs of a failed or missing drum balance weight. In most LG front-load washers, this is caused by a cracked, broken, or detached balance weight assembly. When it fails, the drum loses its counterbalance — producing violent shaking during high-speed spin, banging against the cabinet walls, and triggering unbalanced load error codes even with properly distributed loads. ⚡ Common failure point in LG front-load washers, especially after years of high-speed spin cycles. Part MAG62583007 is the genuine OEM balance weight that restores drum stability and eliminates spin-cycle vibration immediately upon installation.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ Washer powers on and wash cycle runs normally
- ✔ Drum spins freely with no grinding or scraping sounds
- ✔ Washer feet are level and anti-vibration pads have been confirmed as not the issue
- ✔ Vibration is severe and occurs even with small, balanced loads
- ✔ ONLY problem is excessive vibration, shaking, or UE/UB error codes during spin
Not sure? Send us your model number — we'll confirm before you order.
🔧 Common Symptoms
- Washer vibrates violently during spin cycle — most common complaint
- Machine walks or moves across the floor during high-speed spin
- Loud banging or thumping from inside the cabinet during spin
- UE or UB error code displayed even with balanced loads
- Spin cycle stops repeatedly and restarts trying to rebalance
- Visible crack or detachment of the concrete/weight block inside the drum housing
✔ If these symptoms match, this is the most likely failed component in the system.
✔ In most cases, replacing this balance weight restores smooth, quiet spin operation immediately.
📦 Part Details
- Part Number: MAG62583007
- Type: Front-load washer drum balance weight assembly — OEM direct fit
- Replaces: OEM direct-fit balance weight — no modification required
- Brands: LG
While the front panel is open to access the balance weight, inspect the drum bearings and door boot seal for wear or damage — both are common secondary failures in LG front-loaders and are far easier to replace with the cabinet already open than as a separate repair.
⚙️ Installation
Skill Level: MODERATE — 45–60 minutes. Disconnect power and water supply before beginning. Remove the front panel and top panel to access the drum assembly and locate the balance weight mounting bolts at the front of the outer tub. Remove the damaged weight, position the new MAG62583007, and torque the mounting bolts firmly — do not leave them hand-snug as vibration will loosen them. Reassemble in reverse order and run a spin-only cycle to confirm smooth operation before closing the cabinet.
✓ Compatible Models
Confirmed compatible with select LG front-load washer models. Contact us to verify your model number before ordering.
Browse related LG model hubs: WM3770HVA, WM3670HVA, WM3700HWA, WM3700HRA, WM3400CW, WM3700HVA, WM3500CW, LG Washer Parts, LG Appliance Parts.
💡 Pro Tip
Balance weight bolts that are under-torqued will vibrate loose within a few cycles, causing the same violent shaking to return and potentially cracking the new weight. Use a torque wrench and follow the service manual spec for your model — typically 15–20 Nm. A 10-minute step that prevents a repeat repair.
✓ Model-Specific Repair Pages
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Kitchener, Ontario N2E 1W8
- Choosing a selection results in a full page refresh.
