KitchenAid Stand Mixer Missing or Cracked Bowl? Part W11350316 – OEM Replacement Bowl (NLA — Used Stock Only)
A cracked, chipped, or missing stand mixer bowl is one of the most common reasons a KitchenAid mixer becomes unusable — and finding the right OEM replacement is critical for proper fit and safe operation. In KSM6573 series KitchenAid stand mixers, the bowl locks directly onto the mixer base and must be an exact OEM match to seat and rotate correctly. When the bowl is damaged or missing, the mixer cannot be used safely. ⚡ Common wear and damage item in KitchenAid KSM6573-series stand mixers. Part W11350316 is the genuine OEM replacement bowl that restores full mixer function — available in used condition while stock lasts.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ Your mixer powers on and the motor runs normally
- ✔ The mixer head locks and unlocks correctly
- ✔ Attachments (whisk, dough hook, beater) are undamaged
- ✔ ONLY problem is a cracked, chipped, or missing mixer bowl
Not sure? Send us your model number — we’ll confirm compatibility before you order.
🔧 Common Symptoms
- Bowl is cracked, chipped, or broken and cannot hold ingredients safely
- Bowl is missing entirely and mixer cannot be operated
- Bowl does not lock onto the mixer base correctly (check for damage to locking tabs)
- Bowl wobbles or shifts during operation due to damage
- Cosmetic damage (deep scratches, staining) affecting food safety
✔ If these symptoms match, this is the correct replacement component.
✔ Replacing this bowl restores full stand mixer operation immediately.
📦 Part Details
- Part Number: W11350316
- Type: Stand Mixer Bowl — OEM KitchenAid replacement
- Replaces: W10177650, WPW10177650
- Status: No Longer Available (NLA) — Used units only, while stock lasts
- Brands: KitchenAid
While the bowl is off, inspect the bowl-lift lever and locking pin for wear or damage — a worn lift mechanism can prevent the bowl from seating correctly even with a new bowl installed. Also check your flat beater, dough hook, and wire whisk for bent tines or cracks, and replace any damaged attachments at the same time.
⚙️ Installation
Skill Level: Easy — Under 5 minutes. No tools required. Lower the bowl-lift lever to the down position, align the bowl handles with the mixer base slots, seat the bowl onto the base, and raise the lift lever to lock it in place. Test by running the mixer on low speed before adding ingredients.
✓ Compatible Models
Confirmed compatible with: 4KSM6573CCU2, 4KSM6573CER2, 4KSM6573COB2, 4KSM6573CWH2, KSM6573CCU0, KSM6573CCU1, KSM6573CCU2, KSM6573CER0, KSM6573CER1, KSM6573CER2, KSM6573COB0, KSM6573COB1, KSM6573COB2, KSM6573CWH0, KSM6573CWH1, KSM6573CWH2. Contact us to verify your model number before ordering — especially important for NLA parts where used stock is limited.
💡 Pro Tip
W11350316 is discontinued and will not be remanufactured. The only source for this bowl is used OEM stock — which means condition and availability vary. If you’re ordering for a repair, confirm with us before purchasing so we can describe the unit’s condition. If you need a bowl urgently and used stock is gone, the KSM6573 series may accept a compatible aftermarket bowl — contact us and we’ll advise on alternatives.
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Kitchener, Ontario N2E 1W8
- Choosing a selection results in a full page refresh.
