Menu
Whirlpool Microwave Not Working? Control Board W10678766 – Fix No Heat & Error Codes Fast
When a Whirlpool microwave won't heat, displays error codes, or has no power at all, the main control board is the most common cause. In most Whirlpool over-the-range and countertop microwaves, the control board manages every function — power levels, magnetron control, timer, and display. When it fails, the microwave may go completely dead, run without heating, show fault codes, or behave erratically with no pattern. ⚡ Common failure point in Whirlpool-built microwaves after power surges or age-related component failure. Part W10678766 is the genuine OEM replacement control board that restores full microwave operation immediately.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ Microwave has power to the outlet — breaker and fuse confirmed OK
- ✔ Door switches test good (microwave doesn't trip the fuse when door closes)
- ✔ Magnetron and high-voltage components have been ruled out
- ✔ Thermal cutout and thermoprotector are intact
- ✔ ONLY problem is no response from controls, error codes on display, or no heat with all other components OK
Not sure? Send us your model number — we'll confirm before you order.
🔧 Common Symptoms
- Microwave completely dead — no display, no response to any button
- Display shows error codes or fault messages (F1, F2, F3, etc.)
- Microwave runs but doesn't heat food
- Controls are unresponsive or only some buttons work
- Random beeping or display flashing with no input
- Microwave starts then stops mid-cycle for no reason
- Display is blank but microwave otherwise powers on
✔ If these symptoms match, this is the most likely failed component in the system.
✔ In most cases, replacing this control board restores full microwave operation immediately.
📦 Part Details
- Part Number: W10678766
- Type: Main Electronic Control Board (PCB assembly)
- Replaces: OEM direct-fit control board for compatible Whirlpool-built microwaves (no modification required)
- Brands: Whirlpool, Maytag, KitchenAid, Amana, JennAir
⚠️ Recommended While Repairing:
While the cabinet is open, test the door interlock switches — a faulty door switch is the #1 cause of control board damage from power surges and will destroy a new board if not replaced. Replace any door switch that shows resistance or intermittent continuity at the same time.
While the cabinet is open, test the door interlock switches — a faulty door switch is the #1 cause of control board damage from power surges and will destroy a new board if not replaced. Replace any door switch that shows resistance or intermittent continuity at the same time.
⚙️ Installation
Skill Level: ADVANCED — 45–60 minutes. Disconnect power and allow the microwave to sit unplugged for at least 30 minutes before opening — the high-voltage capacitor retains a lethal charge even after power is removed. Remove the outer cabinet, photograph all wire harness connections before disconnecting, then swap the control board and reconnect all harnesses in the original positions. Use ESD precautions when handling the board — static discharge will damage the PCB. Restore power and run a test cycle before reassembling the cabinet.
✓ Compatible Models
This control board fits specific Whirlpool-built microwave models. Contact us with your model number to confirm compatibility before ordering — we'll verify the fit for you.
💡 Pro Tip
Discharge the Capacitor Before Touching Anything:
The high-voltage capacitor inside a microwave can hold a charge of 2,100V or more — enough to be fatal — even hours after unplugging. Before touching any internal component, discharge the capacitor using an insulated screwdriver across its terminals. This is the single most important safety step in any microwave repair and must not be skipped.
The high-voltage capacitor inside a microwave can hold a charge of 2,100V or more — enough to be fatal — even hours after unplugging. Before touching any internal component, discharge the capacitor using an insulated screwdriver across its terminals. This is the single most important safety step in any microwave repair and must not be skipped.
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Address
101 Trillium Dr
Kitchener, Ontario N2E 1W8
Kitchener, Ontario N2E 1W8
Phone
Hours
Mon–Fri 9 AM–5 PM • Sat 9 AM–1 PM
- Choosing a selection results in a full page refresh.
