Menu
Washer Not Draining Properly? Drawer Rack Assembly WW01L01359 – Fix Drawer Failure Fast
A broken or collapsed drawer rack causes your washer drawer to sag, bind, or fall out entirely. In most GE and Hotpoint front-load washers, this is caused by a failed drawer rack assembly. When it fails, the detergent drawer no longer seats correctly, leading to detergent bypass, water leaks at the dispenser, and difficulty opening or closing the drawer. ⚡ Common failure point in GE-built front-load washers. Part WW01L01359 is the genuine OEM replacement that restores proper drawer alignment and dispenser function immediately.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ Your washer powers on and runs cycles normally
- ✔ The drum, motor, and pump all function correctly
- ✔ Water supply to the machine is confirmed OK
- ✔ The dispenser housing itself is intact and undamaged
- ✔ ONLY problem is the drawer sagging, binding, or not staying seated
Not sure? Send us your model number — we'll confirm before you order.
🔧 Common Symptoms
- Detergent drawer droops or sags when pulled open
- Drawer is difficult to open or close — feels stiff or misaligned
- Drawer falls out completely when pulled
- Detergent or fabric softener not dispensing — bypassing the drawer
- Water dripping from the dispenser area during or after cycle
- Visible cracks or broken tabs on the drawer rack or slide rails
✔ If these symptoms match, this is the most likely failed component in the dispenser system.
✔ In most cases, replacing this drawer rack assembly restores normal drawer operation immediately.
📦 Part Details
- Part Number: WW01L01359
- Type: Washer Detergent Drawer Rack / Slide Assembly
- Replaces: OEM direct-fit drawer rack assembly — supersedes WH47M85 (no modification required)
- Brands: GE, Hotpoint
⚠️ Recommended While Repairing:
While the drawer is out, inspect the dispenser housing and inlet valve screen for detergent buildup or cracks — these are common secondary failure points on the same service call. Replacing them together saves a repeat labour visit.
While the drawer is out, inspect the dispenser housing and inlet valve screen for detergent buildup or cracks — these are common secondary failure points on the same service call. Replacing them together saves a repeat labour visit.
⚙️ Installation
Skill Level: EASY — 10–15 minutes. Unplug the washer before beginning. Pull the detergent drawer fully out, depress the release tab, and slide the old rack assembly free from the dispenser housing. Snap the new WW01L01359 rack into place along the guide rails until it clicks, then reinsert the drawer and confirm smooth operation before restoring power.
✓ Compatible Models
Confirmed compatible with select GE and Hotpoint front-load washer models. Contact us to verify your model number before ordering.
💡 Pro Tip
Clean the Dispenser Housing While You're In There:
Detergent residue and mold buildup inside the dispenser housing is the #1 reason drawer racks wear out prematurely. Before installing the new rack, wipe down the housing with a diluted white vinegar solution and run a clean cycle. This extends the life of the new part significantly.
Detergent residue and mold buildup inside the dispenser housing is the #1 reason drawer racks wear out prematurely. Before installing the new rack, wipe down the housing with a diluted white vinegar solution and run a clean cycle. This extends the life of the new part significantly.
Model hub pages: GE Washer Parts, Hotpoint Washer Parts
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Address
101 Trillium Dr
Kitchener, Ontario N2E 1W8
Kitchener, Ontario N2E 1W8
Phone
Hours
Mon–Fri 9 AM–5 PM • Sat 9 AM–1 PM
- Choosing a selection results in a full page refresh.
