THE 8-INCH SURFACE ELEMENT DOES NOT HEAT OR REMAINS ON HIGH
Whirlpool Range Surface Element Control Switch / 8-inch Surface Burner Infinite Switch WP3149400, Fixes The 8-inch surface element does not heat or remains on high
Whirlpool OEM infinite surface-element switch for an 8-inch range burner. The switch controls voltage to the surface-element coil and is used for symptoms such as an element not heating or remaining on high. The documented rating is approximately 240 V and 8.9–11.0 A.
Part WP3149400Replaces 3149400, 99989662, W10295573, 3148954, 314140, 311859, 311858, 311846, 310180Whirlpool
Guaranteed to Fit — or your money back.
Confirm your full appliance model number before ordering.
Confirm your full appliance model number before ordering.
Is This the Right Part?
Part NumberWP3149400
Replaces3149400, 99989662, W10295573, 3148954, 314140, 311859, 311858, 311846, 310180
ManufacturerWhirlpool
Appliance TypeRange
Part TypeSurface Element Control Switch / 8-inch Surface Burner Infinite Switch
✅ Cross Reference Information
Current Part NumberWP3149400
Verified Previous OEM Numbers3149400, 99989662, W10295573, 3148954, 314140, 311859, 311858, 311846, 310180
Common Symptoms
- The 8-inch burner does not turn on.
- The burner remains continuously energized or heats only at high.
- Heat output is inconsistent or cannot be adjusted normally.
- The control knob turns but the associated burner does not respond.
Check Before Replacing
- Disconnect electrical power at the range plug or circuit breaker before inspecting the switch.
- Verify that the affected burner is the 8-inch element associated with this switch and that the control knob and switch shaft engage normally.
- With power disconnected, inspect accessible wiring terminals and connectors for loose connections, overheating, or visible damage; do not rely on visual inspection alone to diagnose the switch.
- If electrical testing is required, have a qualified appliance technician test the switch and related element circuit against the appliance service documentation.
Pro Tip
Before replacing the switch, confirm that the symptom follows the control circuit rather than the surface element, receptacle, wiring, or limiter; an infinite-switch symptom alone does not prove the switch is defective.
Part Details
Part NumberWP3149400
Part TypeSurface Element Control Switch / 8-inch Surface Burner Infinite Switch
ManufacturerWhirlpool
Appliance TypeRange
Primary FunctionControls and regulates voltage supplied to an 8-inch electric range surface-element coil, allowing the burner to cycle between off, low, and high heat.
Installation Notes
- Disconnect electrical power before beginning service.
- Access to the switch generally requires removal of the applicable control-panel or rear-panel covering, depending on the range design.
- Document wire-terminal locations before disconnecting the old switch, then transfer the wires to the corresponding terminals on the replacement.
- Secure the replacement switch in the original mounting position and reinstall removed panels before restoring power.
- Follow the appliance-specific service or installation documentation; the exact access procedure varies by range model.
Verified Compatible Models
RF199LXKT0, RF199LXKT1, RF262LXSB0, RF262LXSQ0, RF262LXST0, RF262LXSW0, RF264LXSB0, RF264LXSQ0, RF264LXST0, RF3165XVW0, RF363PXDN0, RF363PXDW0, RF368LXPS2, WFC315S0JW3, WFC315S0JW4, WFE361LVB1, WFE520C0AS0, YKERI204PB0
Fitment reminder: Match the complete appliance model number, including suffix or revision where applicable, before ordering.
Buy Online Pick Up In-Store
Address
101 Trillium Dr
Kitchener, Ontario N2E 1W8
Kitchener, Ontario N2E 1W8
Phone
Hours
Mon–Fri 9 AM–5 PM • Sat 9 AM–1 PM
