WATER LEAKS DURING DRAINING
Midea Washer Up Drain Hose Assembly 12138000031261, Fixes Water leaks during draining
Genuine Midea up drain hose assembly for compatible top-load washing machines. The hose routes wastewater from the washer tub toward the drain standpipe or laundry sink.
Part 12138000031261Replaces 12138000009819, 301121670012Midea
Guaranteed to Fit — or your money back.
Confirm your full appliance model number before ordering.
Confirm your full appliance model number before ordering.
Is This the Right Part?
Part Number12138000031261
Replaces12138000009819, 301121670012
ManufacturerMidea
Appliance TypeWasher
Part TypeUp Drain Hose Assembly
✅ Cross Reference Information
Current Part Number12138000031261
Replaces12138000009819, 301121670012
Common Symptoms
- Water leaking from the rear or underside of the washer during a drain cycle
- Washer drains slowly or does not drain completely when the hose is kinked, clogged, or damaged
- Visible cracks, splits, holes, brittleness, or collapse in the drain hose
- Washer draining or spinning problems caused by improper hose position or excessive drain height
- Water siphoning or backflow caused by incorrect hose insertion or routing
Check Before Replacing
- Unplug the washer before inspecting the hose or moving the appliance.
- Visually inspect the accessible hose for kinks, crushing, cracks, splits, holes, brittleness, or collapsed sections.
- Confirm the hose is securely connected at its accessible connection points and is not being pinched by the washer or wall.
- Check that the household standpipe or drain accepts water freely; do not assume a washer hose is defective if the household drain is blocked.
- Verify that the hose routing and drain height follow the washer's model-specific installation instructions and that the hose is not inserted too deeply into the drain.
Pro Tip
Before replacing the hose, check routing and drain height first: a kinked hose, blocked household drain, or hose pushed too far into the standpipe can mimic a failed drain hose or cause siphoning.
Part Details
Part Number12138000031261
Part TypeUp Drain Hose Assembly
ManufacturerMidea
Appliance TypeWasher
Primary FunctionRoutes wastewater from the washer tub/drain system to a standpipe, laundry sink, or other approved drain location.
Installation Notes
- Disconnect electrical power before servicing and use care because residual water may remain in the hose.
- Document the original hose routing before removal so the replacement follows the same path.
- Avoid sharp bends, kinks, crushing, or pinching when positioning the replacement hose.
- Reconnect the hose securely at the designated connection points and verify the drain routing and height against the washer's model-specific instructions.
- After installation, run an appropriate drain or rinse test and inspect the hose connections and surrounding area for leaks before returning the washer to normal use.
Verified Compatible Models
ATLMW41, CLAWI47W, CTW41N1AW, CTW45N1AW, CTW45N2AW, LT52N1BWWC, LT52N1BWWCFR, MLV41N1AWW, MLV41N1AWWC, MLV45N1BWW, MLV45N1BWWC, MLV45N3BMG, MLV45N3BWW, MLV47A3AGG, MLV47C3AWW
Fitment reminder: Match the complete appliance model number, including suffix or revision where applicable, before ordering.
Buy Online Pick Up In-Store
Address
101 Trillium Dr
Kitchener, Ontario N2E 1W8
Kitchener, Ontario N2E 1W8
Phone
Hours
Mon–Fri 9 AM–5 PM • Sat 9 AM–1 PM
All brand names are the property of their respective owners and are used for compatibility reference only.
- Choosing a selection results in a full page refresh.
