Menu
Frigidaire Washer Leaking or Not Draining? Internal Drain Hose 134458300 – Stop the Leak and Restore Full Drainage Fast
If your Frigidaire or Electrolux front-load washer is leaking water inside the cabinet or failing to drain completely, a cracked or deteriorated internal drain hose is one of the most common causes. In most Frigidaire front-load washers, the internal drain hose routes water from the wash tub directly to the drain pump. When this hose cracks, splits at a clamp connection, or deteriorates from age and heat exposure, water leaks inside the machine — pooling under the drum, triggering error codes, or causing incomplete drain cycles. ⚡ A leading cause of internal leaks and drain errors on Frigidaire and Electrolux front-load washers. Part 134458300 is the OEM replacement internal drain hose that seals the tub-to-pump connection and restores complete, leak-free drainage.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ Washer powers on and the drum spins normally
- ✔ Water supply and inlet valves are confirmed OK
- ✔ Drain pump runs (you can hear it) but water remains or leaks internally
- ✔ ONLY problem is an internal leak or incomplete drain — not a pump failure or blocked filter
Not sure? Send us your model number — we'll confirm before you order.
🔧 Common Symptoms
- Water pooling under the drum or inside the cabinet after a wash cycle
- Washer displaying drain error codes (E21, E24, or similar) despite a clear filter
- Incomplete drain — water remaining in the tub at the end of the cycle
- Visible cracking, splitting, or deterioration on the internal hose near clamp connections
✔ If these symptoms match, this is the most likely failed component in the system.
✔ In most cases, replacing this internal drain hose stops the leak and restores complete drainage immediately.
📦 Part Details
- Part Number: 134458300
- Type: Washer Internal Drain Hose — Tub-to-Pump — Front-Load
- Replaces: 134458300
- Brands: Frigidaire, Electrolux, Gibson
⚠️ Recommended While Repairing:
While the drain hose is accessible, inspect the drain pump filter and pump inlet port for debris, lint buildup, or damage — a partially blocked pump is often mistaken for a hose failure and can cause the new hose to fail prematurely under back-pressure. Also check the hose clamps at both ends of the drain hose — if the original clamps are corroded or deformed, replace them at the same time to ensure a leak-free seal.
While the drain hose is accessible, inspect the drain pump filter and pump inlet port for debris, lint buildup, or damage — a partially blocked pump is often mistaken for a hose failure and can cause the new hose to fail prematurely under back-pressure. Also check the hose clamps at both ends of the drain hose — if the original clamps are corroded or deformed, replace them at the same time to ensure a leak-free seal.
⚙️ Installation
Skill Level: MODERATE — 30–45 minutes. Disconnect power and water supply before servicing. Access the internal drain hose by removing the front kick panel and tilting the washer back or removing the front panel depending on your model. Release the clamps at both ends of the hose, remove the old hose, and route the new 134458300 hose in the same path. Secure both clamps firmly, restore power and water, and run a short drain cycle to confirm no leaks before reassembling the cabinet.
✓ Compatible Models
Compatible with Frigidaire and Electrolux front-load washer models using the 134458300 internal drain hose. Contact us to verify your model number before ordering.
⚠️ Model-specific Frigidaire washer repair pages: BIDIR hub links pending — handles must be verified before publishing.
Pro Tip — Check the Clamps, Not Just the Hose:
Internal drain hose leaks on Frigidaire front-load washers are often at the clamp connection points rather than the hose body itself. Before ordering a new hose, inspect both clamp ends carefully — if the hose body is intact but the clamp has slipped or corroded, re-seating or replacing the clamp may resolve the leak without replacing the hose. If the hose body is cracked, split, or brittle, replace the full hose assembly and both clamps together for a lasting repair.
Internal drain hose leaks on Frigidaire front-load washers are often at the clamp connection points rather than the hose body itself. Before ordering a new hose, inspect both clamp ends carefully — if the hose body is intact but the clamp has slipped or corroded, re-seating or replacing the clamp may resolve the leak without replacing the hose. If the hose body is cracked, split, or brittle, replace the full hose assembly and both clamps together for a lasting repair.
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Address
101 Trillium Dr
Kitchener, Ontario N2E 1W8
Kitchener, Ontario N2E 1W8
Phone
Hours
Mon–Fri 9 AM–5 PM • Sat 9 AM–1 PM
- Choosing a selection results in a full page refresh.
