A BURNER MAY FAIL TO IGNITE OR MAY HAVE NO/WEAK/INTERMITTENT SPARK WHEN THE ELECTRODE IS DAMAGED OR IMPROPERLY RETAINED
Fisher & Paykel / DCS Range Igniter Kit - Spring and Clip 217994, Fixes A burner may fail to ignite or may have no/weak/intermittent spark when the electrode is damaged or improperly retained
Genuine OEM igniter kit consisting of the igniter, spring, and retaining clip. Fisher & Paykel/DCS documents this part for RDS, RGS, RDT, and RGT ranges, and CS, CP, and CT cooktops.
Part 217994Replaces 210562, 241680Fisher & Paykel / DCS
Guaranteed to Fit — or your money back.
Confirm your full appliance model number before ordering.
Confirm your full appliance model number before ordering.
Is This the Right Part?
Part Number217994
Replaces210562, 241680
ManufacturerFisher & Paykel / DCS
Appliance TypeRange
Part TypeIgniter Kit - Spring and Clip
✅ Cross Reference Information
Current Part Number217994
Replaces210562, 241680
Common Symptoms
- One burner does not ignite while other burners spark normally
- Weak or intermittent sparking at one burner
- Visible cracking or chipping of the igniter’s ceramic insulator
- Igniter electrode is loose, displaced, or not held securely by the spring and clip
Check Before Replacing
- With the appliance cool, electrical power disconnected, and gas supply shut off, visually inspect the igniter ceramic for cracks or chips.
- Check that the electrode is seated and retained by the supplied spring and clip, without forcing or bending the ceramic.
- Compare the affected burner’s electrode position with a matching burner, if accessible without disassembling gas-carrying components.
- Do not test by bypassing safety controls or working around an open gas flame; if electrical or gas-side diagnosis is required, use a qualified technician.
Pro Tip
A no-light condition is not automatically an igniter failure; burner-cap placement, burner-head cleanliness, gas supply, wiring, and the spark module can also affect ignition.
Part Details
Part Number217994
Part TypeIgniter Kit - Spring and Clip
ManufacturerFisher & Paykel / DCS
Appliance TypeRange
Primary FunctionProduces the high-voltage spark at a gas burner to ignite the gas; the spring and retaining clip hold the electrode in position.
Installation Notes
- Disconnect electrical power, shut off the gas supply, and allow the appliance to cool before service.
- Remove only the burner components necessary to access the electrode, following the applicable appliance service or parts-manual instructions.
- Handle the ceramic insulator carefully; do not strike, bend, or overtighten the igniter.
- Install the electrode with the supplied spring and retaining clip so it remains correctly positioned.
- If access requires removing the appliance from cabinetry or exposing gas connections, use an appropriately qualified technician.
Verified Compatible Models
BGB48-BQRL-70494-A, 70015, CTD-304-70694, CTD-365-70692, OR30SLDGX1-70874-A, OR30SNDGX1-70873-A, RDS-364GDSS, RDS-364GLSS, RDS-484GGSS, RDS-486GLSS, RDT485GD-70714, RGB-305, RGS-305, RGS-366, RGS305SS, CS-366SS 70015
Fitment reminder: Match the complete appliance model number, including suffix or revision where applicable, before ordering.
Buy Online Pick Up In-Store
Address
101 Trillium Dr
Kitchener, Ontario N2E 1W8
Kitchener, Ontario N2E 1W8
Phone
Hours
Mon–Fri 9 AM–5 PM • Sat 9 AM–1 PM
All brand names are the property of their respective owners and are used for compatibility reference only.
- Choosing a selection results in a full page refresh.
