Menu
Dishwasher Not Venting? Vent Motor 441335 – Fix Wet Dishes & Steam Buildup Fast
If your dishwasher is leaving dishes wet or steam isn't releasing at the end of the cycle, the vent motor is the most likely cause. In most Whirlpool and KitchenAid dishwashers, the vent motor opens the vent door during the drying cycle to release hot, moist air. When it fails, moisture stays trapped inside — leaving dishes wet, spotted, and smelling stale. ⚡ Common failure point in Whirlpool-built dishwashers. Part 441335 is the genuine OEM replacement that restores proper venting and drying performance immediately.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ Dishwasher powers on and runs full cycles normally
- ✔ Wash and rinse functions work correctly — dishes are clean
- ✔ Water supply and drain confirmed OK — no error codes
- ✔ ONLY problem is dishes coming out wet or vent door not opening during dry cycle
Not sure? Send us your model number — we'll confirm before you order.
🔧 Common Symptoms
- Dishes are wet at the end of the drying cycle
- Steam or condensation remains trapped inside the tub
- Vent door does not open during or after the cycle
- Musty or stale odour inside the dishwasher after a cycle
✔ If these symptoms match, this is the most likely failed component in the system.
✔ In most cases, replacing this vent motor restores normal drying operation immediately.
📦 Part Details
- Part Number: 441335
- Type: Dishwasher Vent Motor — opens the vent door during the heated dry cycle to release moisture
- Replaces: WP441335, AP6010014, PS11743197
- Brands: Whirlpool, KitchenAid, Kenmore
⚠️ Recommended While Repairing:
Check the vent door assembly and vent flap while you have the panel open — if the door is cracked or the flap is warped, replacing the motor alone won't fully restore drying. Replacing both at the same time saves a second service call.
Check the vent door assembly and vent flap while you have the panel open — if the door is cracked or the flap is warped, replacing the motor alone won't fully restore drying. Replacing both at the same time saves a second service call.
⚙️ Installation
Skill Level: MODERATE — 30–45 minutes. Disconnect power before servicing. Remove the inner door panel to access the vent assembly on the upper left side of the door. Disconnect the wiring harness, unclip the old motor, and snap in the replacement. Reconnect the harness and reassemble the door panel.
✓ Compatible Models
Confirmed compatible with WDT780SAEM1, WDF520PADM7, KDTE334GPS0, 665.13743K601 plus additional Whirlpool, KitchenAid, and Kenmore models. Contact us to verify your model number before ordering.
💡 Pro Tip
Run a Rinse Aid Check First:
Before replacing the vent motor, confirm your rinse aid dispenser is full and set to the correct level. Low rinse aid is the #1 misdiagnosed cause of wet dishes — if rinse aid is fine and dishes are still wet, the vent motor is your culprit. Replacing it now avoids a repeat service call.
Before replacing the vent motor, confirm your rinse aid dispenser is full and set to the correct level. Low rinse aid is the #1 misdiagnosed cause of wet dishes — if rinse aid is fine and dishes are still wet, the vent motor is your culprit. Replacing it now avoids a repeat service call.
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Address
101 Trillium Dr
Kitchener, Ontario N2E 1W8
Kitchener, Ontario N2E 1W8
Phone
Hours
Mon–Fri 9 AM–5 PM • Sat 9 AM–1 PM
- Choosing a selection results in a full page refresh.
