Washer Not Spinning? Drive Belt 5304515831 – Fix No-Spin & No-Agitation Fast
If your front-load washer runs but the drum won't spin or agitate, a failed drive belt is the most common cause. In Frigidaire and Electrolux front-load washers, the drive belt transfers motor torque to the drum. When it snaps or stretches, the drum stops moving entirely while the motor continues to run. ⚡ High-failure component in Frigidaire-built front-loaders. Part 5304515831 is the genuine OEM replacement belt that restores full drum rotation and spin function immediately.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ Washer powers on and motor hums normally
- ✔ Water fills and drains correctly
- ✔ Door latch and control board show no fault codes
- ✔ Drum spins freely by hand when unplugged
- ✔ ONLY problem is drum not spinning or agitating during cycle
Not sure? Send us your model number — we'll confirm before you order.
🔧 Common Symptoms
- Drum not spinning — motor runs but clothes sit still in water
- Washer fills and drains but won't agitate
- Loud thumping or slapping noise during spin cycle
- Burning rubber smell from washer cabinet
- Spin cycle starts then stops mid-cycle
- E47 or similar motor overload error code
✔ If these symptoms match, the drive belt is the most likely failed component.
✔ In most cases, replacing this belt restores normal spin and agitation immediately.
📦 Part Details
- Part Number: 5304515831
- Type: Front-load washer drum drive belt
- Replaces: OEM direct-fit drive belt assembly — supersedes 134163500, 134163400 (no modification required)
- Brands: Frigidaire, Electrolux, Crosley
While the front panel is off, inspect the drum bearing and motor pulley for wear — these components often degrade together with the belt. Replacing them in the same service call saves a second labour visit if they fail within months.
⚙️ Installation
Skill Level: Moderate — 30–45 minutes. Unplug the washer before beginning. Remove the front panel to access the drum and motor pulley, loop the new belt around the drum groove and motor pulley, then rotate the drum by hand to seat the belt evenly. Confirm belt tension and alignment before reassembling the cabinet.
✓ Compatible Models
Confirmed compatible with 41761732810, 41761732811, 41761733810, 41771732810, 41771733810, 41771733811, CFLE3900UW0, CFLE3900UW1, CFLE3900UW3, FFLE3900UW0, FFLE3900UW1, FFLE3900UW2, FFLE3900UW3, FFLG3900UW0, FFLG3900UW1, FFLG3900UW2, FFLG3900UW5, FLCE7522AW0, FLCE7522AW1, FLCE7522AW2, FLCE7522AW3, FLCE7523AW0, FLCE752CAW0, FLCE752CAW1, FLCG7522AW0, FLCG7522AW1, plus additional Frigidaire and Electrolux models. Contact us to verify your model number before ordering.
💡 Pro Tip
A worn or cracked motor pulley is the #1 reason a new belt fails prematurely. While you have the cabinet open, spin the pulley by hand and look for wobble, cracks, or rough edges. A replacement pulley costs a few dollars and takes 5 minutes — skipping this check can mean redoing the entire job in 6 months.
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Kitchener, Ontario N2E 1W8
- Choosing a selection results in a full page refresh.
