LG Washer Door Seal Leaking? Boot Clamp ACA56078801 — Fix It Fast
If your LG front-load washer is leaking from the door or the rubber boot seal is pulling away from the drum, the door seal clamp is the most common cause. In most LG WM-series front-load washers, the door boot seal is held in place by a spring-tension clamp ring — when this clamp fatigues, snaps, or loses tension, the seal separates from the tub and water escapes during every cycle. ⚡ Common failure point in LG-built front-load washers. Part ACA56078801 is the genuine OEM replacement clamp that re-seats the boot seal securely and stops door leaks immediately.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ Your washer powers on and runs cycles normally
- ✔ The drum, motor, and pump are functioning correctly
- ✔ The door boot seal rubber itself is intact (not torn or cracked)
- ✔ ONLY problem is the seal pulling away from the tub or water leaking at the door
Not sure? Send us your model number — we'll confirm before you order.
🔧 Common Symptoms
- Water leaking from the front door during or after the wash cycle
- Door boot seal visibly pulling away or sagging from the drum opening
- Musty odour from water pooling under the loose seal
- Clamp ring found loose, broken, or missing inside the door gasket channel
✔ If these symptoms match, the door seal clamp is the most likely failed component.
✔ In most cases, replacing the clamp ring restores a watertight seal immediately.
📦 Part Details
- Part Number: ACA56078801
- Type: OEM Door Boot Seal Clamp Ring — Spring Tension Retaining Clamp
- Replaces: ACA56078802, 4861EN3004L
- Brands: LG, Kenmore
While the door panel is open, inspect the door boot seal (MDS47123604 or equivalent) for tears, cracks, or mould buildup. If the seal is damaged, replace it at the same time — the clamp alone won't stop leaks from a compromised gasket, and labour is identical for both parts.
⚙️ Installation
Skill Level: MODERATE — 20–35 Minutes. Disconnect power before servicing. Remove the door panel trim ring to access the clamp channel, unseat the old clamp, seat the new clamp ring into the gasket groove, and reinstall the trim ring. Run a short cycle and inspect the door seal perimeter for leaks before closing up.
✓ Compatible Models
Confirmed compatible with WM2601HL, WM2601HR, WM2601HW, WM2701HV, WM2801HLA, WM2801HRA, WM2801HWA, WM2901HVA, WM3001HPA, WM3001HRA, WM3001HWA, WM3050CW, WM3070HRA, WM3070HWA, WM3150HVC, WM3150HWC, WM3170CW, WM3250HRA, WM3250HVA, WM3250HWA, WM3360HRCA, WM3360HVCA, WM3360HWCA, WM3370HRA, WM3370HVA, WM3370HWA, WM3470HVA, WM3470HWA, WM3485HWA, WM3550HVCA, WM3550HWCA, WM3570HVA, WM3570HWA, WM3670HWA, WM3875HVCA, WM3875HWCA, WM3885HCCA, WM3885HWCA, WM3997HWA, WM4070HVA, WM4070HWA, WM4270HVA, WM4270HWA, WM4370HKA, WM5000HVA, WM5000HWA, WM8000HVA, WM8000HWA, WM8500HVA, WM9000HVA, WM9000HWA, LSWF388HVS plus additional numeric-prefix LG and Kenmore models. Contact us to verify your model number before ordering.
💡 Pro Tip
Before seating the new clamp, wipe out the gasket groove with a damp cloth and check for debris or mould that could prevent the clamp from seating flush. A clamp installed over a dirty channel will lose tension faster and may allow the seal to pull away again within months. Takes 2 minutes and extends the repair life significantly.
✓ Model-Specific Repair Pages
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Kitchener, Ontario N2E 1W8
- Choosing a selection results in a full page refresh.
