Samsung Range Oven Not Reaching Temperature or Displaying Error Codes? Oven Temperature Sensor DG32-00002B – Fix Heating Failures Fast
If your Samsung range oven won't heat, overheats, or shows temperature error codes, the oven temperature sensor is the most common cause. In most Samsung gas ranges, this is caused by a failed oven RTD temperature sensor. When it fails, the control board loses accurate temperature feedback — the oven may underheat, overheat, display error codes (SE, E-08, tE), or refuse to start a bake cycle entirely. ⚡ Common failure point in Samsung-built gas and electric ranges. Part DG32-00002B is the genuine OEM replacement that restores accurate temperature regulation and normal oven operation.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ QUALIFIER 1 — appliance powers on and runs normally otherwise
- ✔ QUALIFIER 2 — burners and other functions work correctly
- ✔ QUALIFIER 3 — gas supply or power confirmed OK
- ✔ ONLY problem is oven temperature inaccuracy, failure to heat, or temperature-related error codes
Not sure? Send us your model number — we'll confirm before you order.
🔧 Common Symptoms
- Oven not reaching set temperature — food undercooked or takes much longer than expected
- Oven overheating — food burns even at normal temperature settings
- Temperature wildly inconsistent between bake cycles
- Error codes on display: SE, E-08, tE, or similar temperature fault codes
- Oven won't start a bake or broil cycle — control board detects sensor fault
- Oven preheats then shuts off heating element prematurely
- Display shows incorrect temperature reading
- Baking results inconsistent — cakes not rising, cookies burning on one side
✔ If these symptoms match, this is the most likely failed component in the system.
✔ In most cases, replacing the oven temperature sensor restores normal operation immediately.
📦 Part Details
- Part Number: DG32-00002B
- Type: Oven RTD Temperature Sensor (Resistance Temperature Detector)
- Replaces: DG32-00002A, PT1000-S0V9, W10131827, W10131847, 6322B62214A, 2087461, EBG61305805
- Brands: Samsung (verify by model number)
While the oven rear panel is open, inspect the sensor wiring harness and connector for burn marks, broken pins, or heat damage. A damaged harness can cause the same symptoms even after sensor replacement — replacing both at the same time saves a second service call.
⚙️ Installation
Skill Level: EASY — 15–20 minutes, no special tools required. Disconnect power at the breaker before servicing. Open the oven door and remove the 1–2 screws securing the sensor bracket to the rear oven wall. Pull the sensor forward into the cavity to expose the wiring connector, unplug the old sensor, connect the new DG32-00002B, push the wiring back through the rear wall, and secure the bracket. Restore power and run a bake cycle to confirm accurate temperature.
✓ Compatible Models
Confirmed compatible with NX583G0VBBBAA, FER300SB/XAA, FX710BGS/XAA, NE595R0ABSR/AA, NX58F5500SS/AA, NX58H5600SS/AA, FTQ353IWUXXAA, NE59J7630SB/AA, NE59J7630SS/AA, NX58K9500WG/AA, NE63T8311SS/AA, NE63A6511SS/AA, NX60T8711SS/AA, NX60T8311SS/AA plus additional Samsung models — see full list below. Contact us to verify your model number before ordering.
NX583G0VBBBAA, FER300SB/XAA, FX710BGS/XAA, NE595R0ABSR/AA, NE595R0ABSR/AC, NX58F5500SS/AA, NX58H5600SS/AA, FTQ353IWUXXAA, NE59J7630SB/AA, NE59J7630SG/AA, NE59J7630SS/AA, NE59J7630SS/AC, NE59J7630SW/AA, NE59J3421SS/AA, NE59J3421SS/AC, NE59J7750WS/AA, NE59J7750WS/AC, NE59J7850WG/AA, NE59J7850WG/AC, NE59J7850WS/AA, NE59J7850WS/AC, NX58K9500WG/AA, NX58K9500WG/AC, NE59K3321SS/AC, NE59J3420SB/AA, NE59J3420SB/AC, NE59J7651WS/AC, NE59J3420SS/AA, NE59J3420SW/AA, NE59J3420SW/AC, NE59M4310SS/AA, NE59M6850SG/AA, NX58H9500WS/AA, NX58M6650WS/AA, NX58J5600SG/AA, NE59M6850SS/AA, NE59N6630SG/AA, NE59N6630SS/AA, NX58M6650WG/AA, NX58M6630SS/AA, NE59M4320SW/AA, NE59N6650SG/AA, NX58M6630SG/AA, NX58M5600SW/AA, NE59M4310SW/AA, NE59M4320SS/AA, NX58M5600SB/AA, NE59M4310SB/AA, NX58K3310SW/AA, NE59J7650WS/AA, NE59M4320SG/AA, NX58K3310SS/AA, NE59M4320SB/AA, NX58K3310SB/AA, NX58M9420SS/AA, NE59N6650SS/AA, NX58H9500WS/AC, NX58H5600SS/AC, NE59M4320SW/AC, FTQ352IWUW/XAA, NX583G0VBWW/AA, NX58F5700WS/AA, NX58H5650WS/AA, NX583G0VBBB/AA, NX58F5500SB/AA, FTQ352IWUB/XAA, NE594R0ABSR/AA, FTQ352IWUX/XAA, FTQ386LWUX/XAA, NX58H9950WS/AA, FX710BGS/XAC, NX58F5300SS/AA, FX510BGS/XAA, FTQ387LWGX/XAA, NX58F5500SW/AA, NE599N1PBSR/AC, NE595R0ABWW/AA, NE59R4321SS/AC, NE59T4321SW/AA, NE59R4321SS/AA, NE597R0ABSR/AA, NE597R0ABSR/AC, NX58R5601SS, NX60T8711SS/AA, NX58R4311SS/AA, NE63T8711SS/AA, NX60T8311SS/AA, NX58R5601SG/AA, NX58R5601SS/AA, NE63T8511SS/AA, NX58T7511SS/AA, NX60T8111SS/AA, NE63T8111SG/AA, NE59T7511SG/AA, NE63A6511SS/AA, NE63A6511SS/AC, NE63T8311SS/AA, NX60A6111SS, NX60T8751SG
💡 Pro Tip
Before replacing the sensor, test it with a multimeter set to resistance (ohms). At room temperature (~70°F / 21°C), a good DG32-00002B reads approximately 1,080–1,090 ohms. A reading of zero (short), infinite (open circuit), or wildly out of range confirms failure. If resistance reads correctly but errors persist, inspect the wiring harness connector for burn marks or broken pins — the harness may be the real culprit.
New vs. Used — Which Option Is Right for You?
The New (OEM) variant is a fresh factory-spec temperature sensor — ideal for accurate, reliable temperature control long-term. The Used variant is a Certified Pre-Owned sensor pulled from a working unit and tested before sale. Both options ship from XPart Supply Ltd. in Canada.
✓ Model-Specific Repair Pages
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Kitchener, Ontario N2E 1W8
- Choosing a selection results in a full page refresh.
