NE58F9710WS/AA, NE58F9710WS/AC, NE58K9850WS/AA, NE58H9970WS/AA, NE58H9970WS/AC, NE58F9500SS/AA, NE58K9850WG/AA, NE58K9500SG/AA, NE58K9430SS/AA, NY58J9850WS/AA, NE58K9560WS/AA, NE58F9500SS/AC, NE58K9850WG/AC, NE58K9850WS/AC, NY58J9850WS/AC, NE58K9500SG/AC, NE58K9560WS/AC, NE58H9950WS/AA, NE58K9430/AA, NE58R9430SG/AC, NE58R9560WG, NE58R9431ST/AA, NE58R9431SG/AA, NE58R9311SS/AC, NE58R9431SS/AA, NE58R9311SS/AA

🧰 Fix your oven in under 30 minutes!

🧰 Installation / Replacement Tips

Here’s how to replace DG47-00058A properly and what to watch out for:

1. Safety First

• 
  Disconnect power (turn off breaker or unplug range).
  
• 
  Wait for any residual heat / capacitors to discharge.
  
• 
  Use gloves to avoid cuts from sheet metal edges.
  

2. Access the Element

• 
  Pull the range outward from the wall to allow access behind or lift up the cooktop (depending on model).
  
• 
  Usually the back panel needs to be removed (screws or bolts) to reach the element bracket.
  

3. Document Original Setup

• 
  Take photos of wiring, mounts, and orientation.
  
• 
  Note where the bracket(s) and fastening screws go.
  

4. Disconnect the Old Element

• 
  Remove screws or fasteners holding the bracket or shields.
  
• 
  Carefully disconnect the wire terminals (often push‐on spade connectors).
  
• 
  Gently remove the old element.
  

5. Install the New DG47-00058A

• 
  Insert the new element into the correct position, aligning brackets or mounting holes.
  
• 
  Secure with screws / fasteners.
  
• 
  Reconnect the wiring to correct terminals (match polarity if applicable).
  
• 
  Make sure connections are tight and secure.
  

6. Reassemble & Test

• 
  Reinstall the back panel / cover.
  
• 
  Push the range back into position.
  
• 
  Restore power.
  
• 
  Test broil function (the element should glow red).
  
• 
  Use an ohmmeter: a good element often shows resistance in a moderate range (for many broil elements, something like 15–30 Ω is cited in documentation for DG47-00058A at room temp). PartSelect
  

7. Confirm No Shorts or Arcing

• 
  Watch for sparks when first testing.
  
• 
  If display or error codes appear, check wiring and that no part of the element touches metal surfaces.
  

✅ Before You Buy / Replace, Check These

• 
  Model Compatibility: Ensure DG47-00058A is listed in your Samsung range’s parts list.
  
• 
  Dimensions: Confirm length, shape, bracket positions, and mounting hole spacing.
  
• 
  Voltage: This is a 240 V element—don’t use a wrong voltage unit.
  
• 
  Connector Type: Spade connector size and layout should match your range.
  
• 
  Condition: Avoid bent, cracked, or overheated elements.
  
• 
  Warranty & Return: Choose sellers that allow returns or warranty in case it’s a mismatch.

⚠️ Common Symptoms

SymptomDescriptionLikely Cause🔥 Element does not heat / won’t glowBroil or grill function produces no heat at all.Open or burned-out element coil.🌡️ Uneven broiling or grillingFood cooks unevenly; one side gets hotter than the other.Partial coil break or hot spots in the element.⚡ Visible arcing or sparkingSparks appear when the oven is on broil.Insulation breakdown or exposed wires in the element.💡 Oven trips breaker or blows fuseCircuit breaker trips when broil is activated.Shorted element or internal coil fault.🕒 Broil function stops mid-cycleOven shuts off unexpectedly or error codes appear.Overheating or intermittent coil connection.🔩 Physical damageElement appears bent, cracked, or burnt.Mechanical stress, overheating, or age-related failure.

💡 Notes / Troubleshooting Tips

1. 
   Always test resistance with a multimeter before replacing. A properly functioning DG47‑00058A typically measures 15–30 Ω at room temperature (verify exact for your model).
   
2. 
   Check that the wiring and connectors are secure—loose connections can mimic a failed element.
   
3. 
   If multiple symptoms occur (e.g., no heat + breaker trips), replace the element immediately to avoid damage to the oven’s control board or wiring.
   
4. 
   Inspect for burn marks or discoloration around the terminals and mounting brackets.