Menu
Maytag Dishwasher Won’t Start or Showing Error Codes? Control Board 692013-100 – Fix It Fast
A Maytag dishwasher that won’t start, shows error codes, runs erratically, or has a completely unresponsive control panel is almost always caused by a failed main control board. In Maytag and Whirlpool dishwashers, the main control board manages all wash cycle logic — water fill, pump operation, heating, drying, and cycle sequencing. When it fails, the dishwasher may appear dead, start and stop mid-cycle, or display fault codes that won’t clear even after a reset. ⚡ Common failure point on Maytag dishwashers — often caused by power surges, moisture intrusion, or component fatigue over time. Part 692013-100 is the genuine OEM replacement that restores full dishwasher control and cycle operation immediately.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ The dishwasher has power — the door latch engages and the unit is plugged in
- ✔ The control panel (touchpad) has been confirmed functional or replaced
- ✔ Water supply and drain are confirmed OK
- ✔ ONLY problem is the dishwasher not starting, stopping mid-cycle, or showing persistent error codes
Not sure? Send us your model number — we'll confirm before you order.
🔧 Common Symptoms
- Dishwasher completely dead — no response when Start is pressed
- Cycle starts but stops mid-wash and won’t resume
- Persistent error or fault codes that won’t clear after unplugging
- Dishwasher runs but skips stages — no heat, no drain, or no fill
✔ If these symptoms match, this is the most likely failed component in the system.
✔ In most cases, replacing this control board restores full cycle operation immediately.
📦 Part Details
- Part Number: 692013-100
- Type: Dishwasher Main Control Board / Electronic Control Module
- Replaces: 692013-100 (OEM direct)
- Brands: Maytag, Whirlpool
⚠️ Recommended While Repairing:
Before replacing the control board, confirm the control panel (touchpad) is not the actual failure point — a failed touchpad mimics a dead control board. With the board disconnected, test the touchpad membrane for continuity at each button. If the touchpad is faulty, replacing it is significantly cheaper than the control board and will resolve the issue without board replacement.
Before replacing the control board, confirm the control panel (touchpad) is not the actual failure point — a failed touchpad mimics a dead control board. With the board disconnected, test the touchpad membrane for continuity at each button. If the touchpad is faulty, replacing it is significantly cheaper than the control board and will resolve the issue without board replacement.
⚙️ Installation
Skill Level: MODERATE — 20–30 minutes. Disconnect power before servicing. Open the dishwasher door and remove the inner door panel to access the control board mounted behind the control panel fascia. Photograph all wire harness connections before disconnecting, swap the board, and reconnect all harnesses in the same positions. Reassemble the door panel and restore power to confirm full cycle operation.
✓ Compatible Models
Compatible with select Maytag and Whirlpool dishwasher models. Contact us to verify your model number before ordering.
💡 Pro Tip
Control Board vs. Touchpad — Diagnose First:
The most common misdiagnosis on Maytag dishwashers is replacing the control board when the touchpad is the actual failure. The touchpad sends button signals to the board — if those signals never arrive, the board appears dead even though it’s fine. Before ordering this board, try pressing each button firmly and check for any response. If some buttons work and others don’t, the touchpad membrane has failed — not the board. Order the touchpad first; it’s a fraction of the cost.
The most common misdiagnosis on Maytag dishwashers is replacing the control board when the touchpad is the actual failure. The touchpad sends button signals to the board — if those signals never arrive, the board appears dead even though it’s fine. Before ordering this board, try pressing each button firmly and check for any response. If some buttons work and others don’t, the touchpad membrane has failed — not the board. Order the touchpad first; it’s a fraction of the cost.
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Address
101 Trillium Dr
Kitchener, Ontario N2E 1W8
Kitchener, Ontario N2E 1W8
Phone
Hours
Mon–Fri 9 AM–5 PM • Sat 9 AM–1 PM
- Choosing a selection results in a full page refresh.
