Maytag Dishwasher Control Board 692013-100 — Fixes No Start, Error Codes & Unresponsive Controls
Maytag Dishwasher Control Board 692013-100 — Fixes No Start, Error Codes & Unresponsive Controls

Maytag Dishwasher Control Board 692013-100 — Fixes No Start, Error Codes & Unresponsive Controls

Price
$116.94

Frequently Bought Together

Confirm This Fits Your Model
Not sure where to find your model number? See guide →
GENUINE OEM REPLACEMENT PART

Maytag Dishwasher Control Board 692013-100 — Fixes No Start, Error Codes & Unresponsive Controls

A Maytag dishwasher that won’t start, shows error codes, runs erratically, or has a completely unresponsive control panel is almost always caused by a failed main control board. In Maytag and Whirlpool dishwashers, the main control board manages all wash cycle logic — water fill, pump operation, heating, drying, and cycle sequencing. When it fails, the dishwasher may appear dead, start and stop mid-cycle, or display fault codes that won’t clear even after a reset. ⚡ Common failure point on Maytag dishwashers — often caused by power surges, moisture intrusion, or component fatigue over time. Part 692013-100 is the genuine OEM replacement that restores full dishwasher control and cycle operation immediately.

Part 692013-100 Replaces 4444444444444444, 1777040489, c8a400, f0f0f0, ff9800, 692013

Maytag Dishwasher 692013-100

Is This the Right Part?

Part Number692013-100
Replaces4444444444444444, 1777040489, c8a400, f0f0f0, ff9800, 692013
ManufacturerMaytag
Appliance TypeDishwasher

Confirm the complete model number before ordering. Similar parts may use different connectors, dimensions, hose positions, electrical ratings, or mounting points.

  • ✔ The dishwasher has power — the door latch engages and the unit is plugged in
  • ✔ The control panel (touchpad) has been confirmed functional or replaced
  • ✔ Water supply and drain are confirmed OK
  • ✔ ONLY problem is the dishwasher not starting, stopping mid-cycle, or showing persistent error codes
  • Dishwasher completely dead — no response when Start is pressed
  • Cycle starts but stops mid-wash and won’t resume
  • Persistent error or fault codes that won’t clear after unplugging
  • Dishwasher runs but skips stages — no heat, no drain, or no fill
  • Part Number: 692013-100
  • Type: Dishwasher Main Control Board / Electronic Control Module
  • Replaces: 692013-100 (OEM direct)
  • Brands: Maytag, Whirlpool
Control Board vs. Touchpad — Diagnose First:
The most common misdiagnosis on Maytag dishwashers is replacing the control board when the touchpad is the actual failure. The touchpad sends button signals to the board — if those signals never arrive, the board appears dead even though it’s fine. Before ordering this board, try pressing each button firmly and check for any response. If some buttons work and others don’t, the touchpad membrane has failed — not the board. Order the touchpad first; it’s a fraction of the cost.

Part Details

ConditionOEM

Use a qualified technician when diagnosis or installation is outside your experience. Gas parts should be installed by a licensed technician.

✅Compatibility & Cross Reference

692013-100, 4444444444444444, 1777040489, c8a400, f0f0f0, ff9800, 692013

Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.

Buy Online Pick Up In-Store

Address
101 Trillium Dr
Kitchener, Ontario N2E 1W8
Hours
Mon–Fri 9 AM–5 PM • Sat 9 AM–1 PM
Get Directions