OEM Part | Free Shipping | Samsung Front-Load Washer | Manages Fill, Wash, Drain, Spin & Water Level
The Samsung DC92-01063A is a genuine OEM electronic control board for Samsung front-load washers. This main PCB manages all core washer operations — filling, washing, draining, spinning, water level monitoring, and the amount of water entering the machine. It is located under the washer’s top panel at the rear. When this board fails, the washer may not power on, stop mid-cycle, display error codes, or behave erratically.
Find your model below for a confirmed parts list and repair guide:
Don’t see your model? Contact us and we’ll confirm compatibility before ordering.
The DC92-01063A control board is the central processing unit of your Samsung washer, coordinating every stage of the wash cycle. It receives input from sensors (water level, temperature, door lock) and sends commands to the motor, pump, valves, and heating element. The board is located under the top panel at the rear of the machine and connects via multiple wiring harnesses. This is a static-sensitive component — always disconnect power before handling.
Replacing the DC92-01063A typically resolves: washer won’t power on or respond to controls, cycles won’t start or complete, washer stops mid-cycle, error codes displayed on the control panel, incorrect water level or overfilling, washer not draining or spinning, and erratic or unpredictable behavior.
Part Number: DC92-01063A | Brand: Samsung (OEM) | Part Type: Washer Electronic Control Board (Main PCB) | Location: Under top panel, rear of machine | Functions: Fill, wash, drain, spin, water level sensing, motor control | Weight: 5 lbs | HS Code: 850990
OEM / New — The genuine Samsung DC92-01063A manufactured to original factory specifications. This is the same board that came in your washer from the factory. Recommended for exact-fit repairs where OEM quality and compatibility are required. Always disconnect power before servicing; this is a static-sensitive component — handle by the edges only.
Note: aftermarket replacement parts, where available, are not affiliated with, sponsored by, or endorsed by Samsung or any OEM manufacturer.
DC92-01063A (OEM)
Disconnect power to the washer before beginning any repair. This board is static-sensitive — ground yourself by touching an unpainted metal surface before handling. The control board is located under the top panel at the rear of the machine. Remove the top panel screws (typically at the rear), slide the panel back and lift. Photograph all wiring harness connections before disconnecting. Remove the board mounting screws, swap the board, reconnect all harnesses firmly, and replace the top panel. Restore power and run a diagnostic cycle to confirm the repair. Refer to your model’s service manual for error code definitions and test mode procedures.
Please contact us with your full model number to confirm compatibility before ordering. The model number is located on a label inside the door frame of your Samsung washer.
What does the DC92-01063A control board do?
It is the main PCB that manages all washer operations — filling, washing, draining, spinning, water level monitoring, and motor control. When it fails, the washer may not start, stop mid-cycle, display error codes, or fill incorrectly.
How do I know if my Samsung washer control board is bad?
Common signs include the washer not powering on, error codes on the display, cycles that won’t start or complete, incorrect water levels, and the washer stopping mid-cycle. If basic troubleshooting (power cycle, door latch check) doesn’t resolve the issue, the control board is a likely cause. Contact us if you need help diagnosing your model.
Where is the control board located in my Samsung washer?
The DC92-01063A is located under the top panel at the rear of the washer. Access it by removing the rear top panel screws and sliding the panel back.
Can I install this board myself?
Yes — this is a DIY-friendly repair. Disconnect power, photograph all connectors, swap the board, and run a diagnostic cycle. No soldering required. Handle the board by its edges to avoid static damage. Contact us if you need guidance.
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
