Menu
Washer Banging, Vibrating, or Walking Across the Floor? Suspension Rod Kit W10780048 – Fix Drum Balance Failure Fast
Excessive banging, violent vibration, and a washer that walks across the floor during spin are the classic signs of worn suspension rods — and this 4-pack is the complete OEM fix. In most Whirlpool-built top-load washers, this is caused by failed suspension rods with worn plastic end caps or collapsed spring mechanisms. When they fail, the outer tub loses its dampened suspension, slamming against the cabinet during agitation and spin, triggering unbalanced load errors, and accelerating wear on the drum bearings and motor. ⚡ One of the most common wear items on Whirlpool, Maytag, and Amana top-load washers — always replace all four at once. Part W10780048 is the genuine OEM 4-pack replacement that restores full drum suspension, eliminates banging and vibration, and stops the washer from moving during use.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ Your washer powers on and fills/drains normally
- ✔ The drive motor, belt, and transmission are confirmed working
- ✔ The load is not consistently overloaded or unevenly distributed
- ✔ Leveling feet are confirmed adjusted and floor is solid
- ✔ ONLY problem is banging, excessive vibration, unbalanced errors, or washer movement during spin
Not sure? Send us your model number — we’ll confirm before you order.
🔧 Common Symptoms
- Loud banging or thumping during agitation or spin cycle
- Washer vibrates violently and walks across the floor
- Drum appears off-center or tilted inside the cabinet
- Frequent unbalanced load errors stopping the cycle mid-spin
- Visible wear, cracking, or collapse on the plastic rod end caps
- Clothes come out still wet because spin cycle can’t complete at full speed
✔ If these symptoms match, this is the most likely failed component in the system.
✔ In most cases, replacing all four suspension rods restores smooth, quiet operation immediately.
📦 Part Details
- Part Number: W10780048
- Type: Top-Load Washer Suspension Rod Kit – 4-Pack (Complete Set)
- Replaces: W10257087, W10257088, W10349191, W10349193, W10748952, W10821948 — no modification required
- Brands: Whirlpool, Maytag, Amana, Inglis, Kenmore (select models)
⚙️ Installation Notes
Skill Level: Moderate — 30–45 minutes. Disconnect power before servicing. Remove the washer lid and front or rear cabinet panels using a putty knife and Phillips screwdriver to access the tub mounting points, unhook each rod from the tub and cabinet clips using needle-nose pliers, install all four new rods starting from the rear, then reassemble panels and run a full spin cycle to confirm smooth operation. Replace all four rods in a single visit — partial replacement leaves mismatched suspension that causes premature re-failure.
💡 Pro Tip
Always Replace All Four Rods — Never Just One or Two:
If one rod has failed, the other three are at the same wear stage. Replacing only the broken rod leaves three worn rods doing uneven work, which destroys the new rod within months and causes the same banging to return. The 4-pack costs a fraction of a second service call. While you’re inside the cabinet, also inspect the tub bearing for roughness or play — a worn bearing accelerates rod wear and is far cheaper to address now than after the drum drops.
If one rod has failed, the other three are at the same wear stage. Replacing only the broken rod leaves three worn rods doing uneven work, which destroys the new rod within months and causes the same banging to return. The 4-pack costs a fraction of a second service call. While you’re inside the cabinet, also inspect the tub bearing for roughness or play — a worn bearing accelerates rod wear and is far cheaper to address now than after the drum drops.
WTW8600YW0, WTW8240YW0, WTW8200YW0, WTW5700XW2, WTW5640XW2, WTW5610XW2, WTW5600XW2, WTW5550XW2, WTW5500XW2, WTW4950XW2, WTW4930XW3, WTW4910XQ3, WTW4850XQ1, WTW4820XQ0, WTW4800XQ4, WTW4750YQ1, WTW4700YQ0, NTW4700YQ1, NTW4650YQ0, NTW4630YQ0, NTW4610YQ0, NTW4601XQ0, NTW4600YQ1, NTW4501XQ0, MVWX700XW1, MVWX600XW1, MVWX550XW1, MVWX500XW1, MVWC450XW3, MVWC400XW3, MVWC300XW1, MVWC200XW3, ITW4700YQ1, ITW4600YQ1, CAW9444XQ4, CAW9244XQ4, CAW12444XW1, ATW4675YQ0, RTW4740YQ0, RTW4640YQ1, 7MWTW9919DM2, 7MWTW5700YW1, 7MWTW5550YW1, 7MWTW5500XW1, 7MWTW1955YW1, 7MWTW1950YW1, 7MWTW1805DM1, 7MWTW1801BQ1, 7MWTW1750YW1, 7MWTW1715BM1, 7MWTW1709YM1, 7MWTW1604AW1, 7MWTW1602BM1, 7MWTW1504DQ1, 7MWTW1502BM1, 7MWTW1501AW2, 4GWTW4800YQ3, 4GWTW4740YQ3, 4GNTW4600YQ2, 4GNTW4400YQ2, 1CWTW4840YW2, 1CWTW4800YQ2, 1CWTW4740YQ2
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Address
101 Trillium Dr
Kitchener, Ontario N2E 1W8
Kitchener, Ontario N2E 1W8
Phone
Hours
Mon–Fri 9 AM–5 PM • Sat 9 AM–1 PM
- Choosing a selection results in a full page refresh.
