Jenn-Air KitchenAid Oven Igniter W10854967 – OEM Replacement (Replaces 8286725)

Jenn-Air KitchenAid Oven Igniter W10854967 – OEM Replacement (Replaces 8286725)

Price
$40.26

Frequently Bought Together

Confirm This Fits Your Model
Not sure where to find your model number? See guide →
Genuine OEM Replacement Part

Jenn-Air KitchenAid Oven Igniter W10854967 – OEM Replacement (Replaces 8286725)

Part# W10854967 Replaces 8286725 Fits Jenn-Air Fits KitchenAid

Jenn-Air or KitchenAid Gas Oven Not Lighting or Not Heating? Oven Igniter W10854967 – Fix Igniter Failure Fast

A Jenn-Air or KitchenAid gas oven that won’t light, takes multiple attempts to ignite, or heats inconsistently almost always has a failed or weakened oven igniter. In most Jenn-Air and KitchenAid gas ranges and dual-fuel ranges, the oven igniter is the silicon carbide element that draws current to open the gas valve and simultaneously ignites the gas — when it weakens or fails, it can no longer draw enough current to open the valve, and the oven either won’t light at all or takes an extended time to ignite. When it fails, the oven may glow orange but never light, produce a gas smell without ignition, or heat inconsistently from cycle to cycle. ⚡ A weak or failed igniter is the most common cause of a gas oven that won’t heat on Jenn-Air and KitchenAid ranges. Part W10854967 is the genuine OEM oven igniter that restores reliable ignition and consistent oven heating immediately.

❓ Is This the Right Part?

This is the correct fix if ALL of the following are true:

  • ✔ Your range is a compatible Jenn-Air or KitchenAid gas or dual-fuel model (JDRP, JGRP, JGCP, JLRP, KDRS, KFGS, KFGU, KGCU series)
  • ✔ The oven igniter glows orange but the burner does not light — or the oven takes more than 90 seconds to ignite
  • ✔ Gas supply to the range is confirmed — surface burners light normally
  • ✔ The oven control and temperature sensor test within spec
  • ✔ ONLY problem is oven ignition failure — not a gas valve, control board, or temperature sensor fault

Not sure? Send us your model number — we’ll confirm before you order.

🔧 Common Symptoms

  • Oven won’t light — igniter glows but burner never ignites
  • Oven takes more than 90 seconds to light — igniter too weak to open gas valve
  • Gas smell in oven without ignition — valve opening but igniter not hot enough to light
  • Oven heats inconsistently — sometimes lights, sometimes doesn’t
  • Igniter glows dim orange instead of bright orange-white — classic weak igniter signature
  • Oven worked intermittently then stopped lighting entirely

✔ If these symptoms match, this is the most likely failed component in the system.

✔ In most cases, replacing the oven igniter restores reliable ignition and consistent oven heating immediately.

📦 Part Details

  • Part Number: W10854967
  • Type: Gas Oven Igniter — Silicon Carbide Flat Igniter Assembly
  • Replaces: OEM direct-fit igniter — supersedes 8286725 (no modification required)
  • Brands: Jenn-Air, KitchenAid (JDRP, JGRP, JGCP, JLRP, KDRS, KFGS, KFGU, KGCU series gas and dual-fuel ranges)
⚠️ Check the Gas Valve While the Oven Is Open:
A weak igniter that has been failing for an extended period may have caused the gas valve solenoids to wear prematurely from repeated partial-open cycles — if the oven still doesn’t light after replacing the igniter, the gas valve is the next most likely fault. Inspecting the valve while the oven is already disassembled saves a second service call.

⚙️ Installation

Skill Level: Moderate — 20–30 min DIY. Shut off gas supply and disconnect power at the breaker before beginning. Remove the oven bottom panel and broiler drawer to access the igniter mounted to the burner tube. Disconnect the igniter wire harness, remove the mounting screws, and install the new W10854967 igniter in the same position. Reconnect the harness, reinstall the oven bottom, restore gas and power, and test by running the oven to confirm ignition within 60 seconds. Do not touch the igniter element with bare hands — skin oils reduce igniter lifespan.

💡 Pro Tip

Test Igniter Current Draw to Confirm Failure Before Ordering:
A gas oven igniter can be tested with a clamp meter while the oven is calling for heat — a good igniter draws 3.2–3.6 amps; a reading below 3.2 amps confirms the igniter is too weak to open the gas valve even if it still glows. This test takes 60 seconds and definitively confirms igniter failure without guessing, and eliminates the gas valve as a possible cause before you spend money on parts.

Related repair guides and model hubs: Jenn-Air Oven Igniter W10854967, Jenn-Air Oven Not Heating, Jenn-Air Range Parts, KitchenAid Range Parts

✓ Model-Specific Repair Pages

✅Compatibility & Cross Reference

Part number W10854967 replaces 8286725

Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.

Buy Online Pick Up In-Store

Address
101 Trillium Dr
Kitchener, Ontario N2E 1W8
Hours
Mon–Fri 9 AM–5 PM • Sat 9 AM–1 PM
Get Directions