Refrigerator Door Trim Cracked or Broken? Door Trim W11106290 – Restore Your Door Seal Fast
A cracked, broken, or missing refrigerator door trim strip is more than a cosmetic issue — it directly compromises the door gasket seal and allows cold air to escape continuously. In most Whirlpool, KitchenAid, and Maytag refrigerators, the door trim is the structural retainer that locks the door liner and gasket into proper position around the full perimeter of the door. When it breaks, the gasket loses its backing support, pulls away from the door, and the refrigerator works harder to maintain temperature — driving up energy costs and accelerating compressor wear. ⚡ A common structural failure on Whirlpool-platform refrigerators, especially on high-use doors. Part W11106290 is the genuine OEM door trim that restores a factory-correct seal, proper gasket retention, and a clean finished appearance.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ Refrigerator is a Whirlpool, KitchenAid, Maytag, or Amana model
- ✔ Compressor, fans, and cooling system are functioning normally
- ✔ Door closes and latches correctly when trim is intact
- ✔ ONLY problem is cracked, broken, warped, or missing door trim strip
Not sure? Send us your model number — we'll confirm before you order.
🔧 Common Symptoms
- Visible crack, split, or missing section in the door trim strip
- Door gasket pulling away or not seating flush against the cabinet
- Cold air escaping around the door edge — condensation or frost on door exterior
- Refrigerator running more frequently than normal due to seal loss
- Sharp or jagged plastic edge on the door interior or perimeter
- Door liner shifting or flexing when the door is opened or closed
✔ If these symptoms match, this is the most likely failed component in the system.
✔ In most cases, replacing the door trim restores a proper gasket seal and normal energy efficiency immediately.
📦 Part Details
- Part Number: W11106290
- Type: Refrigerator Door Trim Strip – Door Liner Retainer / Gasket Retainer
- Brands: Whirlpool, KitchenAid, Maytag, Amana, Jenn-Air
- Condition: Available as Genuine OEM (new) or Certified Used
While the door trim is removed, inspect the door gasket for tears, hardening, compression set, or deformation — a worn gasket will continue to leak cold air even with a new trim in place. If the gasket doesn’t spring back when pressed or shows any cracking, replace it at the same time to avoid a second disassembly.
⚙️ Installation
Skill Level: Easy — 15–25 minutes. Disconnect power before servicing. The door trim clips or screws into the door liner perimeter — remove the old trim by carefully prying from a corner using a flat tool, working around the full perimeter. Align the new W11106290 trim with the door liner channel and press firmly until all retaining clips engage, or reinstall the retaining screws. Reseat the door gasket if it was displaced, close the door, and verify the seal is flush against the cabinet on all four sides.
✓ Compatible Models
Confirmed compatible with select Whirlpool, KitchenAid, and Maytag refrigerator models. Please contact us to verify your model number before ordering.
💡 Pro Tip
After installing the new door trim and reseating the gasket, close the refrigerator door on a dollar bill at multiple points around the full perimeter. You should feel firm resistance when pulling the bill out — if it slides out easily at any point, the gasket isn’t seating correctly and cold air is escaping at that location. Adjust the trim or gasket alignment before closing up. This 2-minute test confirms a proper seal without any tools.
✓ Model-Specific Repair Pages
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Kitchener, Ontario N2E 1W8
- Choosing a selection results in a full page refresh.
