EXCESSIVE SHAKING OR MOVEMENT DURING SPIN
Whirlpool Washer Suspension Rod Kit W11130362, Fixes Excessive shaking or movement during spin
Genuine Whirlpool OEM suspension rod kit for top-load washing machines. The kit supports the inner tub, reduces vibration and movement, and helps address shaking, spinning issues, banging, and knocking. It includes four suspension rods with springs and suspension ball cups.
Part W11130362Replaces W11228718, W11033491, W10901056, W11027174, W10821710, W10748956, W10780040, W10594080, W10735786Whirlpool
Guaranteed to Fit — or your money back.
Confirm your full appliance model number before ordering.
Confirm your full appliance model number before ordering.
Is This the Right Part?
Part NumberW11130362
ReplacesW11228718, W11033491, W10901056, W11027174, W10821710, W10748956, W10780040, W10594080, W10735786
ManufacturerWhirlpool
Appliance TypeWasher
Part TypeSuspension Rod Kit
✅ Cross Reference Information
Current Part NumberW11130362
ReplacesW11228718, W11033491, W10901056, W11027174, W10821710, W10748956, W10780040, W10594080, W10735786
Common Symptoms
- Washer vibrates or walks across the floor during spin
- Banging, knocking, or thumping caused by excessive tub movement
- Spin cycle problems associated with an unstable or off-balance tub
- Tub appears poorly centered after an unbalanced load
Check Before Replacing
- Disconnect power before inspecting the suspension system.
- With the washer empty and powered off, visually inspect the four suspension rods, springs, and suspension ball cups for visible bending, breakage, dislodgement, or abnormal wear.
- Check that the tub is centered and that each suspension rod is seated correctly in its support points; do not operate the washer if a rod or spring is visibly loose or damaged.
- Confirm the washer is level and test whether redistributing an unbalanced load changes the symptom before attributing the issue to the suspension kit.
- If excessive shaking remains after the load and leveling checks, compare the suspension components with the model-specific service information or consult a qualified technician.
Pro Tip
If suspension wear is suspected, inspect all four rods and their springs and ball cups together; replacing only one visibly weak component can leave the tub unevenly supported.
Part Details
Part NumberW11130362
Part TypeSuspension Rod Kit
ManufacturerWhirlpool
Appliance TypeWasher
Primary FunctionSupports and stabilizes the washer’s inner tub during agitation and spin, helping control tub movement and vibration.
Installation Notes
- Disconnect electrical power before beginning installation.
- Install the complete kit using the model-specific service or installation instructions; suspension layouts and access methods can vary by washer model.
- Ensure all four rods, springs, and suspension ball cups are fully seated and correctly aligned before reassembling the washer.
- After installation, verify that the tub is centered and moves normally by hand with the washer empty and powered off.
- Run the washer only after confirming that no suspension component is loose or contacting surrounding parts.
Verified Compatible Models
7MMVWC565FW0, 7MMVWC565FW1, 7MMVWX655EW0, 7MMVWX655EW1, 8TWTW5010PW0, 8TWTW5010PW1, 8TWTW6000JW1, 11022352510, 11022352511, 11022352512, 11025132410, 11025132412, CAW42114GW0, CAW42114GW1, CAW42114GW2, WTW5000DW1
Fitment reminder: Match the complete appliance model number, including suffix or revision where applicable, before ordering.
Buy Online Pick Up In-Store
Address
101 Trillium Dr
Kitchener, Ontario N2E 1W8
Kitchener, Ontario N2E 1W8
Phone
Hours
Mon–Fri 9 AM–5 PM • Sat 9 AM–1 PM
