Refrigerator Door Side Trim Cracked or Missing? Door Side Trims W11170805 – Fix Door Seal & Appearance Fast
Cracked, broken, or missing refrigerator door side trims allow cold air to escape along the door edges and leave the door liner exposed to moisture and physical damage. In most Whirlpool, KitchenAid, and Maytag refrigerators, the door side trims are the vertical retainer strips that cap the left and right edges of the door liner, holding the gasket channel in alignment and protecting the door structure. When they crack or break, the door gasket loses its anchor point on the sides, cold air escapes, and the door liner becomes vulnerable to further damage. ⚡ A common cosmetic and functional failure on Whirlpool-platform refrigerators. Part W11170805 is the genuine OEM door side trim set that restores proper edge sealing, gasket alignment, and a clean factory appearance.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ Refrigerator is a Whirlpool, KitchenAid, or Maytag model
- ✔ Compressor, fans, and cooling system are functioning normally
- ✔ Door closes and latches correctly when trim is in place
- ✔ ONLY problem is cracked, broken, warped, or missing door side trim strips
Not sure? Send us your model number — we'll confirm before you order.
🔧 Common Symptoms
- Visible crack, break, or missing section in the left or right door side trim
- Door gasket pulling away from the side edges of the door
- Cold air escaping along the door sides — condensation or frost on door edges
- Refrigerator running more frequently than normal due to side seal loss
- Sharp or jagged plastic edge on the door side interior
- Door liner exposed or shifting at the left or right edge
✔ If these symptoms match, this is the most likely failed component in the system.
✔ In most cases, replacing the door side trims restores proper edge sealing and normal energy efficiency immediately.
📦 Part Details
- Part Number: W11170805
- Type: Refrigerator Door Side Trim Set – Vertical Door Edge Retainer / Gasket Channel Trim
- Brands: Whirlpool, KitchenAid, Maytag, Amana, Jenn-Air
- Condition: Available as Genuine OEM (new) or Certified Used
While the door side trims are off, inspect the door gasket along the full perimeter for tears, hardening, or deformation — a damaged gasket will continue to leak cold air even with new trims installed. If the gasket shows any cracking or doesn’t spring back when pressed, replace it at the same time to avoid a second service call.
⚙️ Installation
Skill Level: Easy — 20–30 minutes. Disconnect power before servicing. The door side trims snap or screw into the vertical edges of the door liner — remove the old trims by carefully prying them away from the door liner starting at a corner. Align the new W11170805 trims with the door liner edge channels and press firmly until all clips engage or reinstall the retaining screws. Reinstall the door gasket if it was removed, and verify the door seals flush against the cabinet on all sides.
✓ Compatible Models
Confirmed compatible with select Whirlpool, KitchenAid, and Maytag refrigerator models. Please contact us to verify your model number before ordering.
💡 Pro Tip
After installing the new door side trims and gasket, close the refrigerator door on a dollar bill at several points around the full perimeter — including the sides. You should feel resistance when pulling the bill out. If it slides out easily along the side edges, the gasket isn’t seating correctly at that point. Adjust the trim or gasket alignment before calling the job done.
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Kitchener, Ontario N2E 1W8
- Choosing a selection results in a full page refresh.
