Washer-Dryer Combo Not Filling with Water? Water Inlet Valve W11222849 – Fix No-Fill Fast
A failed water inlet valve is the most common reason a Whirlpool all-in-one washer-dryer combo won't fill, fills too slowly, or fills continuously without stopping. In most Whirlpool combo units, this is caused by a failed solenoid valve assembly. When it fails, the machine may sit at the fill stage indefinitely, throw a fill-related error code, or overfill due to a stuck-open valve. ⚡ Common failure point in Whirlpool-built washer-dryer combos. Part W11222849 is the genuine OEM replacement that restores correct water flow and cycle operation without modification.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ Your unit is a Whirlpool all-in-one washer-dryer combo (WET, WGT, WETLV, WGTLV, YWET series)
- ✔ The machine powers on and other functions (spin, heat, controls) work correctly
- ✔ Water supply hoses are connected, not kinked, and household water pressure is confirmed OK
- ✔ Inlet screens are clear — no blockage at the valve inlet ports
- ✔ The ONLY problem is the unit won't fill, fills too slowly, or won't stop filling
Not sure? Send us your model number — we'll confirm before you order.
🔧 Common Symptoms
- Washer won't fill with water — sits at fill stage, cycle never starts
- Fills very slowly — takes much longer than normal to reach water level
- Continuous filling — water won't shut off, tub overfills
- Intermittent fill — sometimes fills, sometimes doesn't
- Fill-related error codes displayed on control panel
- Audible clicking or buzzing at valve location but no water flow
✔ If these symptoms match, this is the most likely failed component in the system.
✔ In most cases, replacing this water inlet valve restores normal operation immediately.
📦 Part Details
- Part Number: W11222849
- Type: Water Inlet Valve Assembly — Washer-Dryer Combo
- Replaces: OEM direct-fit valve assembly — supersedes W11095119, W11176115, W11177399 (no modification required)
- Brands: Whirlpool (WET, WGT, WETLV, WGTLV, YWET series combos)
While the unit is pulled out for valve access, inspect the inlet hose screens for sediment buildup — clogged screens are often mistaken for valve failure and can cause the new valve to fail prematurely. Replace both inlet hoses if they are more than 5 years old.
⚙️ Installation
Skill Level: Moderate — 45–75 minutes DIY. Unplug the unit and shut off both hot and cold water supply valves before beginning. Disconnect inlet hoses and have a towel ready for residual water. Access the valve from the rear panel — remove the back panel screws, disconnect the wire harness connectors from the old valve, and remove the mounting screws. Install the new W11222849 valve, reconnect harness connectors, reattach inlet hoses, and restore power and water. Run a fill cycle to confirm correct operation and check for leaks at all connections.
✓ Compatible Models
Confirmed compatible with 7MWET4027HW0, 7MWGT4027HW0, 7MWGT4027HW1, WET4027HW0, WET4027HW1, WET4027HW2, WETLV27HW0, WETLV27HW1, WETLV27HW2, WGT4027HW0, WGT4027HW1, WGTLV27HW0, WGTLV27HW1, WGTLV27HW2, WGTLV27HW3, YWET4027HW0, YWET4027HW1. Contact us to verify your model number before ordering.
💡 Pro Tip
Use a multimeter to check solenoid resistance across each valve coil — a healthy coil reads roughly 200–500Ω; an open or shorted coil confirms valve failure. This takes 2 minutes and eliminates guesswork. If both coils read open, the valve is definitely the culprit.
7MWET4027HW0, WET4027HW0, WET4027HW1, WET4027HW2, WETLV27HW0, WETLV27HW1, WETLV27HW2, WGT4027HW0, WGT4027HW1, WGTLV27HW0, WGTLV27HW1, WGTLV27HW2, WGTLV27HW3, YWET4027HW0, YWET4027HW1, YWET4027HW2
✓ Model-Specific Repair Pages
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Kitchener, Ontario N2E 1W8
- Choosing a selection results in a full page refresh.
