Washer Not Agitating or Not Spinning? W11239857 Drive Belt – Fix No Agitation & No Spin Fast

No agitation, no spin, or a burning rubber smell are the clearest signs your washer drive belt has failed. In most Whirlpool-platform belt-driven VMW top-load washers, this is caused by a glazed, cracked, or snapped W11239857 drive belt. When it fails, the motor runs but torque never reaches the splutch or drive system — the basket sits still or won’t reach full RPM. ⚡ Common failure point in WTW, MVW, NTW, and ATW series washers. Part W11239857 is the genuine OEM replacement that restores full agitation and spin immediately.

❓ Is This the Right Part?

This is the correct fix if ALL of the following are true:

• ✔ Washer powers on and motor hums or runs
• ✔ Water fills and drains correctly
• ✔ Lid switch and door latch confirmed OK
• ✔ Splutch and pulleys show no obvious damage (inspect while replacing)
• ✔ ONLY problem is no/weak agitation, no/weak spin, burning smell, or squeal on start

Not sure? Send us your model number — we’ll confirm before you order.

🔧 Common Symptoms

• Washer not agitating — most common complaint, motor runs but basket doesn’t move
• Washer not spinning or basket won’t reach full RPM
• Burning rubber smell during wash or spin cycle
• Squealing or squeaking noise on startup
• Intermittent “won’t spin with a full load” complaint
• Visible belt debris or rubber residue inside the cabinet

✔ If these symptoms match, the W11239857 drive belt is the most likely failed component in the system.

✔ In most cases, replacing this belt restores full agitation and spin immediately.

📦 Part Details

• Part Number: W11239857
• Type: Washer drive belt — high-friction ribbed rubber, belt-driven VMW top-load platform
• Replaces: OEM direct-fit drive belt — supersedes W10808317, 5EPJ556 (no modification required)
• Brands: Whirlpool, Maytag, Amana, Kenmore, Inglis

⚙️ Installation

Skill Level: MODERATE — 30–45 minutes. Unplug the washer before beginning. Tip the unit forward onto its front panel (place a blanket to protect the finish) to access the drive system from below — no need to fully disassemble the cabinet. Remove the old belt from the motor pulley and basket drive pulley, route the new W11239857 around both pulleys, and verify it seats in all ribs evenly. Restore the washer to upright, plug in, and run a spin cycle to confirm full RPM before closing up.

💡 Pro Tip

🔗 Model Hub Pages

Find part compatibility guides and repair resources for your specific model: WTW4655JW0, WTW4655JW1, WTW4850HW0, WTW4850HW1, WTW4850HW2, WTW4855HW0, WTW4855HW1, WTW4855HW2, WTW4915EW2, WTW4950HW0, WTW4950HW1, WTW4950HW2, WTW4955HW0, WTW4955HW1, WTW4955HW2, WTW5000DW2, WTW5000DW3, WTW5005KW0, WTW5100HC0, WTW5100HW0, WTW5105HC0, WTW5105HW0, WTW6120HC0, WTW6120HW0, MVW5035MW0, MVW5430MW0, MVW6200KW0, MVW6230HC0, MVW6230HW0, MVW6230RHW0, MVWC416FW1, MVWC465HW0, MVWC565FW2, MVWX655DW2, NTW4516FW3, NTW4519JW0, ATW4516HW0, ATW4516MW0, ITW4871FW3, ITW4880HW0, CAW38125HW0, CAW42114GW2.

✓ Model-Specific Repair Pages