Whirlpool Front-Load Washer Won’t Drain, Won’t Spin, or Has Standing Water? Drain Pump W11458345 – Fix Drain Failures Fast

A failed drain pump assembly is the most common cause of a Whirlpool or Maytag front-load washer that won’t drain, leaves standing water in the tub, or displays F9E1, F21, or F9E2 error codes. In most Whirlpool and Maytag front-load washers, the drain pump assembly is responsible for removing all water from the tub during the drain and spin cycles. When it fails — due to a seized impeller, burned motor, or foreign object obstruction — water stays trapped, the washer can’t advance to spin, and clothes come out soaking wet. ⚡ Most common drain system failure in Whirlpool and Maytag front-load washers. Part W11458345 is the genuine OEM replacement that restores full drain and spin operation immediately — directly supersedes W10918608, W11316609, and W11319789, no modification required.

❓ Is This the Right Part?

This is the correct fix if ALL of the following are true:

• ✔ Washer powers on and fills and agitates normally
• ✔ Drain hose confirmed not kinked, clogged, or improperly routed
• ✔ Pump filter/coin trap cleaned and confirmed clear of debris
• ✔ Door latch confirmed functional and sealing correctly
• ✔ ONLY problem is washer not draining, standing water remaining after cycle, or F9E1/F21/F9E2 error codes

Not sure? Send us your model number — we'll confirm before you order.

🔧 Common Symptoms

• Washer won’t drain — standing water in tub after cycle — most common customer complaint
• F9E1, F21, or F9E2 error codes displayed on control panel
• Washer fills and agitates but won’t transition to spin
• Clothes come out soaking wet after a full cycle
• Humming or grinding noise when washer should be draining
• Washer stops mid-cycle with water still in the tub

✔ If these symptoms match, this is the most likely failed component in the system.

✔ In most cases, replacing this drain pump assembly restores full drain and spin operation immediately.

📦 Part Details

• Part Number: W11458345
• Type: Washer Drain Pump Assembly — complete pump and motor assembly for front-load washers
• Replaces: OEM direct-fit assembly — supersedes W10918608, W11316609, W11319789 (no modification required)
• Brands: Whirlpool, Maytag

⚙️ Installation Notes

Skill Level: MODERATE — 30–45 minutes. Disconnect power and have towels ready — residual water will spill when the pump is disconnected. The pump is accessed from the front lower panel or by tilting the washer back depending on model. Disconnect the wiring harness and hose clamps, remove the mounting screws, and swap the pump assembly. Reconnect hoses and harness, restore power, and run a drain/spin cycle to confirm full water evacuation before reassembling the access panel.

✓ Compatible Models

Confirmed compatible with WFW5620HW0, WFW5620HW1, WFW5620HW2, WFW5620HW3, WFW6620HW0, WFW6620HW1, WFW6620HW2, WFW6620HC0, WFW6620HC1, WFW6620HC2, WFW8620HW0, WFW8620HW1, WFW8620HW2, WFW8620HC0, WFW8620HC1, WFW8620HC2, WFW560CHW0, WFW560CHW1, WFW862CHC0, WFW862CHC1, WFC9820HW0, WFC9820HC0, MHW5630HW0, MHW5630HW1, MHW5630HC0, MHW5630HC1, MHW6630HW0, MHW6630HW1, MHW6630HW2, MHW6630HC0, MHW8630HW0, MHW8630HW1, MHW8630HW2, MHW8630HC0, MHW8630HC1, MHW8630HC2, NFW5800HW0, NFW5800HW1, NFW5800HW2, IFW5900HW0, IFW5900HW1, IFW5900HW2, 7MWFW560CHW0, 7MWFW560CHW1, 7MWFW560CHW2, 7MWFW5622HW0, 7MWFW5622HW2, 7MWFW6621HC0, 7MWFW6621HC2, 7MWFW6622HW0, 7MWFW6622HW2, 7MWFC9822HC0, 7MWFC9822HC1, 7MWFC9822HW0, 7MMHW6621HC0, 7MMHW6621HC2, 7MMHW6621HW0, 8TWFW6620HW0, 8TWFW8620HW1, 8TMHW6630HW0, plus additional Whirlpool and Maytag front-load models. Contact us to verify your model number before ordering.

💡 Pro Tip

✓ Model-Specific Repair Pages