Dishwasher Not Draining? Drain Pump W11462456 – Fix Standing Water Fast

Standing water at the bottom of your dishwasher after a cycle is almost always a failed drain pump — and W11462456 is the OEM fix. In most Whirlpool-built dishwashers, failure to drain is caused by a seized or burned-out drain pump motor. When it fails, dirty water sits in the tub after every cycle, the dishwasher may stop mid-cycle with an error code, and foul odours develop quickly from stagnant water. ⚡ Common failure point in Whirlpool-platform dishwashers including KitchenAid, Maytag, and JennAir. Part W11462456 is the genuine OEM replacement drain pump that restores full drainage and eliminates standing water immediately.

❓ Is This the Right Part?

This is the correct fix if ALL of the following are true:

• ✔ Dishwasher powers on and runs through wash cycles normally
• ✔ Water supply and inlet valve are confirmed working
• ✔ Filter and drain hose have been checked and are clear of blockages
• ✔ Appliance is a Whirlpool-platform dishwasher (Whirlpool, KitchenAid, Maytag, or JennAir)
• ✔ ONLY problem is water remaining in the tub after the cycle ends

🔧 Common Symptoms

• Standing water at the bottom of the dishwasher after a cycle
• Dishwasher stops mid-cycle and won't drain
• Drain error code displayed (e.g. F8E1, E2)
• Humming sound at end of cycle but no water draining
• Dishwasher drains slowly or incompletely
• Foul odour from stagnant water in the tub

✔ If these symptoms match, the drain pump is the most likely failed component in the system.

✔ In most cases, replacing the drain pump with W11462456 restores full drainage immediately.

📦 Part Details

• Part Number: W11462456
• Type: Genuine OEM Dishwasher Drain Pump — Item #14 in parts diagram
• Replaces: W11193157 — no modification required
• Brands: Whirlpool, KitchenAid, Maytag, JennAir

⚙️ Installation Notes

Skill Level: MODERATE — 30–45 minutes, basic appliance experience recommended. Disconnect power and shut off the water supply before servicing. The drain pump is accessed from below the dishwasher — lay the unit on its back or side, disconnect the wire harness and drain hose connections (have towels ready for residual water), twist out the old pump, and seat the new W11462456 in its place. Photograph all connections before disconnecting.

💡 Pro Tip

BLB14GRANA1, BLB14GRANA2, BLB14GRANA3, JDPSG244LS0, JDPSG244LS1, JDPSG244LS2, JDPSG244PS0, JDPSG244PS1, JDPSS244LL0, JDPSS244LL1, JDPSS244LL2, JDPSS244LM0, JDPSS244LM1, JDPSS244LM2, JDPSS244PL0, JDPSS244PL1, JDPSS244PM0, JDPSS244PM1, JDPSS245LX0, JDPSS245LX1, JDPSS246LL0, JDPSS246LL1, JDPSS246LM0, JDPSS246LM1, KDFE204KBL0, KDFE204KBL1, KDFE204KBL2, KDFE204KBL3, KDFE204KBS0, KDFE204KBS1, KDFE204KBS2, KDFE204KBS3, KDFE204KPS0, KDFE204KPS1, KDFE204KPS2, KDFE204KPS3, KDFE204KWH0, KDFE204KWH1, KDFE204KWH2, KDFE204KWH3, KDFE304RBS0, KDFE304RPS0, KDTE204KBL0, KDTE204KBL1, KDTE204KBL2, KDTE204KBL3, KDTE204KBS0, KDTE204KBS1, KDTE204KBS2, KDTE204KBS3, KDTE204KPS0, KDTE204KPS1, KDTE204KPS2, KDTE204KPS3, KDTE204KWH0, KDTE204KWH1, KDTE204KWH2, KDTE204KWH3, KDTE304LPA0, KDTE304LPA1, KDTE304RBS0, KDTE304RPS0, WDPS7024RV0, WDPS7024RZ0, WDTA80SAKZ0, WDTA80SAKZ1, WDTA80SAKZ2, WDTA80SAKZ3, WDTS7024RZ0