Washer Not Dispensing Detergent? Detergent Dispenser W11524105 — Fix Leaks & Dispensing Failures Fast
Detergent pooling in the drawer or never reaching the drum is a dispenser failure — not a cycle issue. In most Whirlpool-platform front-load washers, this is caused by a failed detergent dispenser housing or valve. When it fails, detergent sits in the tray, overflows onto the door gasket, or bypasses the drum entirely — leaving clothes under-cleaned and accelerating mold buildup in the drawer cavity. ⚡ Common failure point in Whirlpool-built front-load washers. Part W11524105 is the genuine OEM replacement dispenser that restores precise, cycle-timed detergent delivery and eliminates drawer leaks permanently.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ Washer powers on and runs cycles normally
- ✔ Water fills and drains correctly
- ✔ Detergent supply and type confirmed OK (not overdosing HE detergent)
- ✔ ONLY problem is detergent not dispensing, pooling in drawer, or leaking from dispenser
Not sure? Send us your model number — we'll confirm before you order.
🔧 Common Symptoms
- Detergent or fabric softener left in dispenser drawer after cycle completes
- Water pooling or leaking out of the dispenser drawer during wash
- Dispenser drawer stiff, hard to open, or won't close fully
- Mold or residue buildup in drawer that returns after cleaning
- Washer dispensing at wrong cycle stage (too early or not at all)
- Visible cracks, broken tabs, or warped housing on existing dispenser
✔ If these symptoms match, this is the most likely failed component in the system.
✔ In most cases, replacing this detergent dispenser restores normal operation immediately.
📦 Part Details
- Part Number: W11524105
- Type: Washer Detergent Dispenser Housing Assembly
- Replaces: W10918512, W11318755, W11437243, W11465532, W11486348
- Brands: Whirlpool, Maytag, Amana, Inglis
- Condition: New Genuine OEM
- Ships From: Canada
If the dispenser drawer slide rails or housing mounting tabs are cracked, the new dispenser won't seal correctly. Inspect the drawer track and door gasket while the unit is apart — replacing damaged rails at the same time eliminates the most common cause of repeat leaks.
⚙️ Installation
Skill Level: Easy — 15–30 minutes. Disconnect power before servicing. Pull the dispenser drawer fully out of the machine, depress the release tab, and unclip the dispenser housing from the front panel. Swap the assembly, confirm all tabs seat flush, and reinstall the drawer. No tools required on most models.
✓ Compatible Models
Confirmed compatible with 7MWFC9822HC, WFW9620HW0, WFW8620HW0, WFW6620HW0, WFW5620HW0, WFW560CHW0, NFW5800HW0, IFW5900HW0, WFC9820HW0 plus additional Whirlpool, Maytag, Amana, and Inglis models. Contact us to verify your model number before ordering.
💡 Pro Tip
If the dispenser housing is cracked from water pressure rather than physical damage, the inlet valve solenoid may be delivering water at too high a pressure. A failing inlet valve is the second most common cause of repeat dispenser failures on these platforms — replacing both at the same time prevents a callback.
✓ Model-Specific Repair Pages
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Kitchener, Ontario N2E 1W8
- Choosing a selection results in a full page refresh.
