WASHER DOES NOT FILL OR HAS INTERMITTENT/INCORRECT WATER FILLING WHEN THE HARNESS OR ITS CONNECTIONS ARE OPEN, DAMAGED, OR LOOSE
Whirlpool Washer Harness, Water Inlet Valve W11524851, Fixes Washer does not fill or has intermittent/incorrect water filling when the harness or its connections are open, damaged, or loose
Genuine Whirlpool washer water-inlet-valve wire harness. It connects to the washer's water inlet valve/dispenser assembly.
Part W11524851Replaces W11130934Whirlpool
Guaranteed to Fit — or your money back.
Confirm your full appliance model number before ordering.
Confirm your full appliance model number before ordering.
Is This the Right Part?
Part NumberW11524851
ReplacesW11130934
ManufacturerWhirlpool
Appliance TypeWasher
Part TypeHarness, Water Inlet Valve
✅ Cross Reference Information
Current Part NumberW11524851
ReplacesW11130934
Common Symptoms
- No water entering the washer during a fill cycle
- Slow or intermittent filling caused by an unreliable electrical connection
- One fill function or temperature selection not operating when the associated harness circuit is open
- Water-inlet-valve circuit fault after the valve itself tests within specification
Check Before Replacing
- Disconnect power before inspecting the harness.
- With power disconnected, visually inspect the harness for damaged insulation, loose connectors, corrosion, pinched wires, or terminals that are not fully seated.
- Confirm that each harness connector is fully engaged with the control board and the appropriate water-inlet-valve terminals.
- Check the washer’s water supply and inlet hoses separately before attributing a no-fill condition to the harness.
- If qualified to use an ohmmeter, check harness continuity only with the washer unplugged and connectors isolated; compare results with the applicable model’s technical sheet or service documentation.
Pro Tip
If the water-inlet-valve coils test within the applicable specification but the washer still reports a fill-circuit problem, inspect the harness connectors and continuity before replacing the valve or control board.
Part Details
Part NumberW11524851
Part TypeHarness, Water Inlet Valve
ManufacturerWhirlpool
Appliance TypeWasher
Primary FunctionCarries electrical signals between the washer control system and the water-inlet-valve/dispenser assembly, allowing the washer to energize the valve solenoids during fill.
Installation Notes
- Disconnect electrical power before servicing.
- Document connector locations and wire routing before removal.
- Disconnect the harness from the control board and water-inlet-valve assembly, then reconnect the replacement harness to the same corresponding locations.
- Ensure connectors are fully seated and wires are routed and retained as in the original installation, away from moving or pinching areas.
- After reassembly, reconnect the water hoses and restore the water supply and electrical power; check for proper filling and leaks.
Verified Compatible Models
WTW500CMW0, WTW500CMW1, WTW6120HC3, WTW6120HW2, WTW6120HW3, WTW6150PB0, WTW6150PW0, WTW6150PW1, WTW6157PB0, WTW6157PB1, WTW6157PW0, WTW7120HC1, WTW7120HW1, WTW8127LC1, WTW8127LC2, WTW8127LC3, WTW8127LW1, WTW8127LW2, WTW8127LW3, ZWW5310RB0, ZWW5310RB1
Fitment reminder: Match the complete appliance model number, including suffix or revision where applicable, before ordering.
Buy Online Pick Up In-Store
Address
101 Trillium Dr
Kitchener, Ontario N2E 1W8
Kitchener, Ontario N2E 1W8
Phone
Hours
Mon–Fri 9 AM–5 PM • Sat 9 AM–1 PM
