Washer Leaking or Not Draining? Drain Hose W11551765 — Fix It Fast
If your front-load washer is leaking water onto the floor, draining slowly, or throwing a drainage error code, the drain hose is one of the first components to inspect. In most Whirlpool-built front-load washers, the drain hose cracks, kinks, or deteriorates over time — preventing water from exiting the drum properly. When it fails, water pools under the machine, cycles stop mid-wash, or the washer displays F9/E1 or similar drain error codes. ⚡ Common failure point in Whirlpool, Maytag, Amana, and Inglis front-load washers. Part W11551765 is the genuine OEM replacement drain hose that restores leak-free drainage and eliminates error codes caused by a failed or restricted hose.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ Your washer powers on and the drum spins normally
- ✔ Water fills into the drum correctly
- ✔ The drain pump runs (you can hear it) but water isn't exiting properly
- ✔ ONLY problem is water leaking from the hose area or slow/incomplete draining
Not sure? Send us your model number — we'll confirm before you order.
🔧 Common Symptoms
- Water pooling on the floor behind or under the washer
- Washer stops mid-cycle with a drain error code (F9E1, F9E2, or similar)
- Drain cycle takes much longer than normal
- Visible cracks, kinks, or soft spots on the existing drain hose
✔ If these symptoms match, this is the most likely failed component in the drain system.
✔ In most cases, replacing the drain hose restores normal drainage and clears error codes immediately.
📦 Part Details
- Part Number: W11551765
- Type: OEM Front-Load Washer Drain Hose Assembly
- Replaces: W11392677
- Brands: Whirlpool, Maytag, Amana, Inglis
While the back panel is off and the drain hose is disconnected, inspect the drain pump filter and pump inlet for debris (coins, lint, small items). A clogged pump is often the root cause of drain hose stress and premature failure. Clearing it now prevents the same problem from recurring.
⚙️ Installation
Skill Level: EASY — 20–30 minutes. Basic tools required. Disconnect power and turn off the water supply before servicing. Pull the washer away from the wall and remove the back access panel. Disconnect the old drain hose from the pump outlet and the standpipe or utility sink. Route the new W11551765 hose in the same path, secure the clamps, and restore power to run a drain cycle to confirm no leaks.
✓ Compatible Models
Confirmed compatible with: 7MMHW6621HC1, 7MMHW6621HW1, 8TMHW6630HW0, 8TWFW5620HW0, 8TWFW6620HW0, 8TWFW8620HW0, IFW5900HW2, MHW5630HC0, MHW5630HW0, MHW6630HC3, MHW8630HC3, MHW8630HW3, NFW5800HW2, WFW5620HW3, WFW8620HC3, WFW8620HW3, WFW9620HC2, WFW9620HW2, WFW9620HBK2, and additional Whirlpool, Maytag, and Amana front-load models. Contact us to verify your model number before ordering.
💡 Pro Tip
Whirlpool recommends the drain hose outlet be positioned between 39" and 96" from the floor. If the standpipe is too low, water will siphon back into the drum and cause repeated drain errors even with a brand-new hose. Confirm standpipe height before closing up — it's a 30-second check that prevents a frustrating callback.
✓ Shop by Appliance Type
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Kitchener, Ontario N2E 1W8
- Choosing a selection results in a full page refresh.
