Refrigerator Not Cooling or Freezing Up? Evaporator Assembly W11598433 – Fix No-Cool & Frost Failures Fast
When your Whirlpool, KitchenAid, or Maytag refrigerator stops cooling properly or develops heavy frost on the back wall, the evaporator assembly is the most likely failed component. In most French door and side-by-side refrigerators across these brands, this is caused by a failed evaporator assembly. When it fails, the refrigerator loses the ability to absorb heat from the cabinet — resulting in warm temperatures, excessive frost accumulation on the evaporator coils, and compressor overrun. ⚡ Common failure point in Whirlpool-platform French door refrigerators. Part W11598433 is the genuine OEM replacement that restores full evaporator function, proper airflow, and normal cooling performance immediately.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ Refrigerator compressor runs but fresh food or freezer section is not cooling
- ✔ Evaporator fan motor is confirmed operational (air moving in freezer)
- ✔ Defrost heater and thermostat have been tested or ruled out
- ✔ ONLY problem is insufficient cooling, heavy frost on back freezer wall, or warm fresh food section
Not sure? Send us your model number — we'll confirm before you order.
🔧 Common Symptoms
- Refrigerator section warm despite freezer appearing to run
- Heavy frost or ice sheet covering the back wall of the freezer compartment
- Evaporator coils completely blocked with ice — no airflow through the evaporator
- Compressor runs continuously but temperatures rise over time
✔ If these symptoms match, this is the most likely failed component in the system.
✔ In most cases, replacing this evaporator assembly restores normal cooling and airflow immediately.
📦 Part Details
- Part Number: W11598433
- Type: Refrigerator Evaporator Assembly (complete coil and housing unit)
- Replaces: W11337412, W11515437, W11547656
- Brands: Whirlpool, KitchenAid, Maytag, JennAir
While the evaporator is out, test and replace the defrost heater assembly and defrost thermostat — a failed defrost system is the leading cause of evaporator icing and will destroy a new evaporator assembly if not corrected. Replacing all three components in one visit eliminates the most common repeat failure on these platforms.
⚙️ Installation
Skill Level: ADVANCED — 60–90 minutes. Disconnect power and allow the freezer to fully defrost before servicing. Remove freezer shelving, the rear panel, and all wiring harness connections to access the evaporator. Transfer any attached sensors or brackets to the new assembly, reinstall in reverse order, and allow 24 hours for the refrigerator to reach stable operating temperatures after restoration.
✓ Compatible Models
Confirmed compatible with KRFC300ESS, KRFC302EBS, KRFF305ESS, WRF535SWHZ, WRF540CWHZ, MFC2062FEZ, MFF2558FEZ, MRFF5036PZ, WRFA35SWHZ, JFC2089BEP, JFFCF72DKL series and additional Whirlpool-platform models. Contact us to verify your model number before ordering.
💡 Pro Tip
The evaporator on these Whirlpool-platform refrigerators fails almost exclusively because the defrost heater or thermostat stopped working — allowing ice to build up until the coil is completely blocked. Installing a new evaporator without fixing the defrost system means you’ll be doing this repair again in 6–18 months. The defrost heater and thermostat together are typically under $40 and add 15 minutes to the job.
✓ Model-Specific Repair Pages
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Kitchener, Ontario N2E 1W8
- Choosing a selection results in a full page refresh.
