WASHER MAY FAIL TO DRAIN, AGITATE, OR SPIN WHEN THE LOWER HARNESS OR ITS CONNECTORS ARE DAMAGED
Whirlpool Washer Lower wire harness (HARN LOWER 4.7/4.8) W11643701, Fixes Washer may fail to drain, agitate, or spin when the lower harness or its connectors are damaged
Genuine Whirlpool OEM lower wire harness used in select Whirlpool, Maytag, and Crosley top-load washers. The harness connects lower washer electrical components, including the motor, drain pump, and shift actuator, to the control system.
Part W11643701Replaces W11335100Whirlpool
Guaranteed to Fit — or your money back.
Confirm your full appliance model number before ordering.
Confirm your full appliance model number before ordering.
Is This the Right Part?
Part NumberW11643701
ReplacesW11335100
ManufacturerWhirlpool
Appliance TypeWasher
Part TypeLower wire harness (HARN LOWER 4.7/4.8)
✅ Cross Reference Information
Current Part NumberW11643701
ReplacesW11335100
Common Symptoms
- Won't drain or leaves water in the tub
- No agitation or spin
- Intermittent motor, pump, or shift-actuator operation
- Washer operation changes when wiring moves or vibrates
- Visible chafing, broken insulation, corrosion, burned areas, or damaged terminals on the lower harness
Check Before Replacing
- Disconnect washer power before inspecting the harness.
- Visually inspect the lower harness and connectors for broken insulation, chafing, pinching, corrosion, burned areas, loose terminals, or disconnected plugs.
- Pay particular attention to the harness branch and connector serving the drain pump, as well as areas near moving parts and cabinet edges.
- Confirm that connectors are fully seated and that the harness is not pulled tight or rubbing against the cabinet.
- If electrical testing is required, use the appliance's model-specific wiring diagram and service procedure; do not test energized wiring unless qualified to do so.
Pro Tip
Photograph the complete harness routing and connector locations before removal. Reinstall the replacement along the original path and keep it clear of moving parts and sharp edges to help prevent repeat chafing or strain damage.
Part Details
Part NumberW11643701
Part TypeLower wire harness (HARN LOWER 4.7/4.8)
ManufacturerWhirlpool
Appliance TypeWasher
Primary FunctionRoutes electrical power and control signals between the washer control system and lower components, including the drive motor, drain pump, and shift actuator.
Installation Notes
- Disconnect electrical power and water supplies before servicing.
- Access the lower harness according to the washer's model-specific service instructions.
- Document connector positions and the original routing before disconnecting the old harness.
- Disconnect and reconnect connectors carefully, confirming each connector is fully seated.
- Route the harness through the original clips or guides and keep it away from moving parts, sharp edges, and pinch points.
- Perform the model-specific diagnostic or test cycle after reassembly.
Verified Compatible Models
8TWTW5010PW0, 8TWTW5010PW1, 8TWTW5057PW0, 8TWTW5057PW1, CAW45125LW0, CAW45125LW1, CWW4512RW0, MVW4505MW0, MVW4505MW1, MVW4505MW2, MVW5035MW0, MVW5035MW1, MVW5035MW2, MVW5430MW0, MVW5430MW1
Fitment reminder: Match the complete appliance model number, including suffix or revision where applicable, before ordering.
Buy Online Pick Up In-Store
Address
101 Trillium Dr
Kitchener, Ontario N2E 1W8
Kitchener, Ontario N2E 1W8
Phone
Hours
Mon–Fri 9 AM–5 PM • Sat 9 AM–1 PM
