⚠ This part has been superseded by a newer OEM part number.
WE11M00071 has been replaced by WW02F00468. We recommend ordering the current part for guaranteed fit and full lifespan.
Order WW02F00468 Instead →Dryer Not Heating? GE Mica Heating Element WE11M00071 – Fix No-Heat Fast
If your GE electric dryer runs but produces no heat, a failed mica heating element is the most common cause. In most GE and Hotpoint electric dryers, this is caused by a failed mica heating element. When it fails, the drum tumbles normally but clothes come out cold and damp regardless of cycle length or temperature setting. ⚡ Common failure point in GE-built electric dryers. Part WE11M00071 is the genuine OEM replacement that restores full heating performance and gets your dryer back to normal operation.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ Dryer powers on and drum tumbles normally
- ✔ Timer, controls, and door switch function correctly
- ✔ Household circuit breaker and outlet confirmed OK
- ✔ ONLY problem is no heat or insufficient heat during drying cycle
Not sure? Send us your model number — we'll confirm before you order.
🔧 Common Symptoms
- Dryer runs but produces no heat at all
- Clothes remain damp after a full drying cycle
- Dryer takes multiple cycles to dry a normal load
- Heating element visibly burned, broken, or open when inspected
✔ If these symptoms match, this is the most likely failed component in the system.
✔ In most cases, replacing this mica heating element restores normal operation immediately.
📦 Part Details
- Part Number: WE11M00071
- Type: Mica Electric Heating Element — OEM dryer heat source assembly
- Replaces: WE11X20397, WW02F00338, WW02F00468, WE11M30, 189D7110G014, 212D1512G03000
- Brands: GE, Hotpoint, RCA
Check and replace the thermal fuse (WE4M519) while the dryer is open — if the heating element failed due to overheating, the thermal fuse is likely blown too. Replacing both at the same time prevents a repeat no-heat call and saves a second disassembly.
⚙️ Installation
Skill Level: MODERATE — 30–45 minutes. Disconnect power before servicing. Remove the dryer back panel to access the heating element housing, disconnect the wiring harness and mounting screws, swap in the new element, and reassemble in reverse order. No special tools required beyond a nut driver and Phillips screwdriver.
✓ Compatible Models
Confirmed compatible with GCMX180ED5WW, GTMP280ED4WW, GTMP280ED5WW, GTMP280ED6WW, GTMP520ED4WW, GTMP520ED5WW, GTMP520ED6WW, GTMS570ED5WW, GTMX100ED4WW, GTMX100ED5WW, GTMX180ED3WW, GTMX180ED4WW, GTMX180ED5WW, GTMX180ED6WW, GTX18ESBJ0WW, GTX18ESMJ0WW, HTMX050EF4WW, MTMX050EF3WW, MTMX050EF4WW, MTMX050EF5WW, GMMP280ED5WS, GMMP280ED6WS plus additional GE and Hotpoint models. Contact us to verify your model number before ordering.
💡 Pro Tip
The thermal fuse is a one-time safety device that blows when the element overheats. If your element failed, there's a high probability the fuse is open too. Order WE4M519 alongside this element — it costs a few dollars and eliminates the risk of reassembling the dryer only to find it still won't heat because the fuse is blown.
✓ Model-Specific Repair Pages
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Kitchener, Ontario N2E 1W8
- Choosing a selection results in a full page refresh.
