Menu
Washer Dryer Not Drying? Heat Pump Module WG01F08108 – Fix Heat Pump Failure Fast
If your GE or Monogram washer dryer combo is running but not drying clothes, the heat pump module is the most common culprit. In GE ventless washer dryer units, the heat pump module and support assembly manages the entire thermal cycle — when it fails, the drum spins but no heat is generated, leaving clothes wet at the end of every cycle. ⚡ Common failure point in GE-built ventless washer dryer combos. Part WG01F08108 is the genuine OEM replacement that restores full drying performance and energy-efficient operation immediately.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ Unit powers on and the wash cycle completes normally
- ✔ Drum rotates and water drains correctly
- ✔ Household power supply and circuit breaker confirmed OK
- ✔ Control board shows no unrelated fault codes
- ✔ ONLY problem is clothes remaining wet / no heat during dry cycle
Not sure? Send us your model number — we'll confirm before you order.
🔧 Common Symptoms
- Clothes still wet after full dry cycle — most common complaint
- Dryer runs but produces no heat
- Cycle completes but drum interior stays cold
- Unit takes multiple cycles to partially dry a load
- Error code related to heat pump or thermal system displayed
- Unusual noise from heat pump compressor area during dry cycle
✔ If these symptoms match, this is the most likely failed component in the system.
✔ In most cases, replacing this heat pump module restores normal drying operation immediately.
📦 Part Details
- Part Number: WG01F08108
- Type: Heat Pump Module & Support Assembly – ventless washer dryer thermal system
- Replaces: OEM direct-fit heat pump assembly — supersedes WG04F12834 (no modification required)
- Brands: GE, Monogram
⚠️ Recommended While Repairing:
While the heat pump module is out, inspect the evaporator coils and condensate drain path for blockages — a clogged drain is often what accelerated the original module failure. Clearing it now prevents repeat failures and saves a second service call.
While the heat pump module is out, inspect the evaporator coils and condensate drain path for blockages — a clogged drain is often what accelerated the original module failure. Clearing it now prevents repeat failures and saves a second service call.
⚙️ Installation
Skill Level: ADVANCED — 60–90 minutes. Disconnect power to the unit before beginning. The heat pump module is accessed by removing the rear or lower service panel depending on your model; the assembly unbolts from its support bracket and refrigerant lines must be carefully disconnected. Follow GE's service documentation for refrigerant handling requirements — this repair may require a certified technician in some jurisdictions.
💡 Pro Tip
Check the Lint Filter and Condenser Before Ordering:
A severely clogged lint filter or blocked condenser can mimic heat pump failure by starving the system of airflow. Clean both thoroughly and run a test cycle first — if the unit still won't heat, the WG01F08108 module is your fix. This 5-minute check can save you the cost of a part you don't need.
A severely clogged lint filter or blocked condenser can mimic heat pump failure by starving the system of airflow. Clean both thoroughly and run a test cycle first — if the unit still won't heat, the WG01F08108 module is your fix. This 5-minute check can save you the cost of a part you don't need.
Find all parts for your model: CPA2412NXDG0 parts hub, PFQ97HSPV0DS parts hub
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Address
101 Trillium Dr
Kitchener, Ontario N2E 1W8
Kitchener, Ontario N2E 1W8
Phone
Hours
Mon–Fri 9 AM–5 PM • Sat 9 AM–1 PM
- Choosing a selection results in a full page refresh.
