Microwave Not Heating or Won't Start? Capacitor WG02F00228 – Fix No-Heat Fast

A failed high-voltage capacitor is one of the most common causes of a microwave that runs but produces no heat, or won't start at all. In most GE, Monogram, and Café over-the-range and built-in microwaves, the capacitor stores and releases the high-voltage charge that powers the magnetron. When it fails, the microwave may hum, display normally, and run its timer — but produce zero heat. ⚡ Common failure point in GE-built microwave high-voltage circuits. Part WG02F00228 is the genuine OEM replacement that restores full heating power immediately.

❓ Is This the Right Part?

This is the correct fix if ALL of the following are true:

• ✔ Microwave powers on and display/controls work normally
• ✔ Turntable rotates and interior light functions
• ✔ Door switches and interlock confirmed OK
• ✔ Magnetron and diode tested and not shorted
• ✔ ONLY problem is no heat output or unit won't start heating cycle

Not sure? Send us your model number — we'll confirm before you order.

🔧 Common Symptoms

• Microwave runs but food is not heated
• Unit hums loudly but produces no heat
• Microwave trips breaker or blows fuse during operation
• Burning smell from high-voltage section
• Microwave starts then immediately stops
• No heat on any power level

✔ If these symptoms match, this is the most likely failed component in the high-voltage circuit.

✔ In most cases, replacing this capacitor restores full heating operation immediately.

📦 Part Details

• Part Number: WG02F00228
• Type: High-Voltage Microwave Capacitor — OEM GE / Monogram / Café
• Replaces: WB27X10308, WB27X10520, WB27X10701, WB27X10747, WB27X11033, WG02F05993, WG02F08474, 0CZZW1H004P — no modification required
• Brands: GE, Monogram, Café, Profile

⚙️ Installation Notes

Skill Level: ADVANCED — 30–45 minutes. Disconnect power and unplug the microwave before servicing. ⚠️ CRITICAL: The capacitor retains a lethal high-voltage charge even when unplugged — discharge it fully using an insulated resistor before touching any components. Remove the outer cabinet, locate the high-voltage capacitor near the magnetron, disconnect leads, swap the capacitor, and reassemble. Verify polarity and lead orientation match the original before powering on.

💡 Pro Tip

[FLAGGED] CSB913M2N2S5, [FLAGGED] CSB913P3N3D1, [FLAGGED] CSB923M2N2S5, [FLAGGED] CSB923P2N2S1, [FLAGGED] CSB923P4N2W2, [FLAGGED] CTC912P2N2S1, [FLAGGED] CVM517P2M6S1, [FLAGGED] CVM517P2R1S1, [FLAGGED] CVM517P3M6D1, [FLAGGED] CVM517P3R1D1, [FLAGGED] CVM517P4M6W2, [FLAGGED] CVM517P4R1W2, [FLAGGED] JT3800SH8SS, [FLAGGED] JT3800SH9SS, [FLAGGED] PT7800SH9SS, [FLAGGED] PT7800SHASS, [FLAGGED] ZSB9131N2SS, [FLAGGED] ZSB9132N2SS, [FLAGGED] CEB1590SS3SS, [FLAGGED] CSB913P2N1S1, [FLAGGED] CSB913P2N2S1, [FLAGGED] CT9800SHSS, [FLAGGED] CVM517P2M5S1, [FLAGGED] CVM517P3M5D1, [FLAGGED] CVM517P4M5W2, [FLAGGED] PEB2060SM2SS, [FLAGGED] ZSB9231N1SS, [FLAGGED] ZSB9231N2SS, [FLAGGED] ZSB9232N1SS, [FLAGGED] ZSB9232N2SS, [FLAGGED] ZSC1001KSS01, [FLAGGED] ZSC1001KSS02, [FLAGGED] ZSC2201J2SS, [FLAGGED] ZSC2202J2SS

✓ Model-Specific Repair Pages