GE Microwave Damper Assembly WG02F05334 (Replaces WB06X10938, WB38M00612)
GE Microwave Damper Assembly WG02F05334 (Replaces WB06X10938, WB38M00612)

GE Microwave Damper Assembly WG02F05334, Replaces 253602603184, WB06X10938, WB38M00612

XPart Number XP10009444
$23.99
$26.15
Available by special order
Title: OEM Genuine

Product variant with selected options does not exist!

Frequently Bought Together

Check Fit & Find Parts
Bubba checks verified models, product descriptions, cross-references and store data. Find your model number →
POOR OR UNCONTROLLED MICROWAVE EXHAUST AIRFLOW

GE Microwave Damper Assembly WG02F05334, Fixes Poor or uncontrolled microwave exhaust airflow

Genuine OEM GE damper assembly used in the ventilation or airflow system of select GE over-the-range microwave models. The part regulates exhaust airflow and helps prevent backdrafts.

Part WG02F05334Replaces 253602603184, WB06X10938, WB38M00612GE
Guaranteed to Fit — or your money back.
Confirm your full appliance model number before ordering.

Is This the Right Part?

Part NumberWG02F05334
Replaces253602603184, WB06X10938, WB38M00612
ManufacturerGE
Appliance TypeMicrowave
Part TypeMicrowave Damper Assembly

✅ Cross Reference Information

Current Part NumberWG02F05334
Replaces253602603184, WB06X10938, WB38M00612

Common Symptoms

  • Weak or ineffective ventilation during vent-fan operation
  • Rattling or flapping noise from the exhaust area
  • Damper flap stuck open or closed
  • Cold air or drafts entering through the microwave when the vent is off
  • Visible warping, cracking, or damage to the damper flap

Check Before Replacing

  • With the microwave and vent fan turned off, observe the damper area if accessible and check for obvious obstruction, warping, or a flap that is visibly stuck.
  • Run the vent fan and verify that airflow is present at the exterior exhaust outlet; poor airflow can also be caused by ducting, filters, or the exterior cap, so do not attribute the symptom to the damper alone.
  • Listen for abnormal rattling or repeated flapping from the damper during vent-fan operation.
  • After disconnecting electrical power and only if the model’s service instructions provide access, inspect whether the damper flap moves freely without forcing it or disassembling the assembly.

Pro Tip

Before replacing the damper, check the complete ventilation path—including the grease filter, duct, exterior wall or roof cap, and backdraft conditions—because restricted ducting can mimic a failed damper.

Part Details

Part NumberWG02F05334
Part TypeMicrowave Damper Assembly
ManufacturerGE
Appliance TypeMicrowave
Primary FunctionRegulates exhaust airflow through the microwave ventilation system, helping direct heat, steam, and odors into the exhaust duct while limiting backdrafts when the vent is not operating.

Installation Notes

  • Disconnect electrical power before accessing or replacing the damper assembly.
  • Verify the appliance model and the old part’s orientation before installation; the damper must align with the microwave exhaust path.
  • Inspect the duct connection and exterior exhaust opening for blockage before closing the installation area.
  • After installation, operate the vent fan and confirm that airflow is directed through the intended exhaust path and that the damper does not rattle or bind.

Verified Compatible Models

CVM1599SVC01, CVM1655STC01, JVM1625STC01, JVM1630BFC01, JVM1630BTC01, JVM1630WFC01, JVM1630WTC01, JVM1635SFC01, JVM1635SFCA01, JVM1635SLJC01, JVM1635STC01, JVM3160RF5SS, MCAS724M1WW, PVM2188SJC01, HMV1472B1HS, HMV1472B2HS, HMV1472B3HS, HMV1472B4HS

Fitment reminder: Match the complete appliance model number, including suffix or revision where applicable, before ordering.

What Customers Say

Buy Online Pick Up In-Store

Address
101 Trillium Dr
Kitchener, Ontario N2E 1W8
Phone
1-877-899-7278
Hours
Mon–Fri 9 AM–5 PM • Sat 9 AM–1 PM
Get Directions
Map showing warehouse location at 101 Trillium Dr, Kitchener
View on Google Maps