The WG03F09165 is the genuine OEM replacement compressor for GE French-door and counter-depth refrigerators. The compressor is the heart of the refrigeration system — it pressurizes refrigerant and drives the entire cooling cycle. When it fails, the fridge stops cooling entirely: food spoils, the freezer warms up, and the unit may run constantly without dropping temperature. This is a direct OEM replacement for CFE28, CYE22, CWE23, ZWE23, GWE23, PYE22, PYD22, and GYE22 series models. Replaces WG03A03987, WG03F09135, WR87X41785, and WR87X41607.
⚠️ Professional installation required. Compressor replacement involves handling refrigerant (R-600a or R-134a) and requires EPA-certified technicians and specialized equipment. This part is sold for professional service use. Do not attempt DIY installation without proper certification and tools.
✓ Is This the Part You Need?
This compressor fits GE CFE28, CYE22, CWE23, ZWE23, GWE23, PYE22, PYD22, and GYE22 series French-door and counter-depth refrigerators. Confirm your full model number in the Compatible Models section below before ordering. If your model isn’t listed, contact us to verify compatibility — this is a high-value freight part.
✓ Symptoms This Part Fixes
✓ Fridge not cooling at all
✓ Freezer warming up
✓ Compressor won’t start or run
✓ Compressor runs but no cooling
✓ Fridge runs constantly, never reaches temp
✓ Loud clicking or buzzing from compressor area
✓ Food spoiling faster than normal
✓ Compressor confirmed failed by technician
✓ Part Details
Part Number: WG03F09165
Type: Refrigerator Compressor
Cross-Reference / Replaces: WG03A03987, WG03F09135, WR87X41785, WR87X41607
Fits: GE CFE28, CYE22, CWE23, ZWE23, GWE23, PYE22, PYD22, GYE22 series
Installation: Professional installation required — refrigerant handling certification mandatory
Shipping: Free shipping — oversized freight item
✓ Installation Notes
Skill Level: Professional only — EPA/refrigerant certification required.
Professional Time: 2–4 hours
-
Disconnect power — Unplug the refrigerator completely before beginning.
-
Recover refrigerant — Use certified recovery equipment to remove all refrigerant from the system. Do not vent to atmosphere.
-
Access compressor — Remove the rear access panel and disconnect the compressor wiring harness and refrigerant lines.
-
Remove old compressor — Unbolt the compressor from its mounting grommets and remove from the unit.
-
Install WG03F09165 — Mount the new compressor on the grommets, reconnect refrigerant lines, and secure all fittings.
-
Replace filter-drier — Always install a new filter-drier when replacing the compressor. A contaminated drier will destroy the new compressor.
-
Evacuate and recharge — Pull a deep vacuum on the system, then recharge with the correct refrigerant type and weight per the model’s data plate.
-
Test — Restore power and verify the compressor starts, runs, and the system reaches target temperatures within 4–6 hours.
✓ Compatible Models
Contact us to confirm compatibility with your model before ordering.
💡 Pro Tip — Always Replace the Filter-Drier at the Same Time:
A compressor failure often contaminates the system with debris, moisture, and burnt oil. If you install a new WG03F09165 without replacing the filter-drier, the contamination will circulate through the new compressor and destroy it within weeks. The filter-drier is a $15–25 part — never skip it on a compressor replacement. Also flush the refrigerant lines if the old compressor showed signs of burnout (black oil, burnt smell). One skipped step on a $680 part is an expensive lesson.
