DISHWASHER LEAVES WATER IN THE TUB AFTER DRAIN
GE (general Electric) Dishwasher Pump And Drain Kit WG04A04002, Replaces WD26X21254, Fixes Dishwasher leaves water in the tub after drain
Genuine GE dishwasher drain pump and pump-and-drain kit. The assembly removes water from the dishwasher tub during the drain phase and includes five clamps according to one established parts distributor.
Part WG04A04002Replaces WD26X21254GE (General Electric)
Guaranteed to Fit — or your money back.
Confirm your full appliance model number before ordering.
Confirm your full appliance model number before ordering.
Is This the Right Part?
Part NumberWG04A04002
ReplacesWD26X21254
ManufacturerGE (General Electric)
Appliance TypeDishwasher
Part TypeDishwasher pump and drain kit
✅ Cross Reference Information
Current Part NumberWG04A04002
ReplacesWD26X20423, WD35X10384, WD35X20553, WG04A01093, WG04A02642, WG04F09565, WG04F10449, WG04L04531
Common Symptoms
- Standing water remains after a completed cycle
- Dishwasher does not drain or drains slowly
- Water leakage may occur from a damaged pump or pump seal
- Unusual humming, buzzing, grinding, or scraping may occur if the pump is obstructed or failing
Check Before Replacing
- Disconnect electrical power before inspecting the dishwasher or pump area.
- Check and clean the dishwasher filters and sump area for food debris or other obstructions.
- Inspect the drain hose for kinks, blockage, or incorrect routing; verify the required high loop or air gap arrangement for the model.
- Check the sink drain, garbage-disposer connection, and air gap for blockage; if a disposer was recently installed, verify that its dishwasher drain knockout plug was removed.
- During a drain portion of a cycle, observe whether water moves through the drain path and note whether the pump produces an unusual sound. Do not assume the pump is defective until hose, filter, sump, and plumbing restrictions are excluded.
Pro Tip
A no-drain symptom is not pump-specific: GE identifies filters, the sump, drain hose, sink/disposer connection, air gap, and drain-hose routing as possible causes, so check those restrictions before replacing the pump kit.
Part Details
Part NumberWG04A04002
Part TypeDishwasher pump and drain kit
ManufacturerGE (General Electric)
Appliance TypeDishwasher
Primary FunctionRemoves wastewater from the dishwasher tub during the drain phase through the drain hose.
Installation Notes
- Disconnect electrical power before installation and remove standing water carefully to limit spills.
- Use the model-specific GE service or installation instructions for access, disconnection, and reassembly; dishwasher pump layouts vary by model.
- Replace the complete assembly and included clamps only after confirming the part matches the appliance model and the drain system is not blocked.
- After installation, run an appropriate test or short cycle and check the drain operation and pump area for leaks.
✅ Cross Reference Information
WD26X21254
Verified Compatible Models
GDF510PGJ2WW, GDF520PGD6WW, GDT545PGJ2BB, GDT545PGJ2WW, GDT580SGF6WW, GDT655SGJ2WW, GDT680SSH2SS, PDT750SSF2SS
Fitment reminder: Match the complete appliance model number, including suffix or revision where applicable, before ordering.
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Address
101 Trillium Dr
Kitchener, Ontario N2E 1W8
Kitchener, Ontario N2E 1W8
Phone
Hours
Mon–Fri 9 AM–5 PM • Sat 9 AM–1 PM
- Choosing a selection results in a full page refresh.
