WASHER MAY FAIL TO START OR ADVANCE THROUGH A CYCLE
GE / General Electric Washer electronic control board WG04F04565, Fixes Washer may fail to start or advance through a cycle
Genuine OEM electronic control board/control assembly for GE top-load washers. The board manages washer functions including filling, washing, draining, agitation, spinning, and cycle control.
Part WG04F04565Replaces WH12X10538, WH12X10614GE / General Electric
Guaranteed to Fit — or your money back.
Confirm your full appliance model number before ordering.
Confirm your full appliance model number before ordering.
Is This the Right Part?
Part NumberWG04F04565
ReplacesWH12X10538, WH12X10614
ManufacturerGE / General Electric
Appliance TypeWasher
Part TypeWasher electronic control board
✅ Cross Reference Information
Current Part NumberWG04F04565
ReplacesWH12X10538, WH12X10614
Common Symptoms
- Cycle will not start or advance
- Washer does not fill, drain, agitate, or spin
- Cycles run unusually long or short
- Washer becomes unresponsive or behaves erratically
Check Before Replacing
- Disconnect power before inspecting the control assembly or its wiring.
- Confirm the appliance model and replacement part number match before ordering or installing.
- With power disconnected, inspect accessible control-board connectors and wiring for loose connections, visible damage, corrosion, or heat discoloration.
- Because other components can cause similar symptoms, check the relevant water-supply, drain, door/lid-interlock, and drive-system conditions before attributing the fault to the control board.
- If service information for the specific washer calls for a reset, diagnostic test, or calibration after board replacement, follow that model-specific procedure.
Pro Tip
Do not diagnose the control board from a single generic washer symptom; this board controls multiple functions, so first verify connections and rule out the related valves, pump, motor, sensors, and safety interlocks.
Part Details
Part NumberWG04F04565
Part TypeWasher electronic control board
ManufacturerGE / General Electric
Appliance TypeWasher
Primary FunctionControls washer cycle sequencing and coordinates filling, washing, draining, agitation, and spinning through the washer’s electronic control system.
Installation Notes
- Disconnect electrical power before servicing.
- Handle the electronic assembly carefully and avoid unnecessary contact with circuit-board surfaces.
- Access and connector-removal details vary by washer model; use the model-specific service information.
- Reconnect wiring exactly as found and verify all connectors are fully seated before restoring power.
- A reset, diagnostic test, or calibration may be required after installation when specified by the model’s service information.
Verified Compatible Models
GCWN4950D0WS, GCWN4950D1WS, GCWN4950D2WS, GHWN4250D0WW, GHWN4250D1WW, GHWN4250D2WW, GMAN4250F0WS, GMAN4250F1WS, GTAN4250D0WW, GTAN4250D1WW, GTAN4250D2WW, GTAP2250D0WW, GTAP2250D1WW, GTWN4250D0WS, GTWN4250D1WS
Fitment reminder: Match the complete appliance model number, including suffix or revision where applicable, before ordering.
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Address
101 Trillium Dr
Kitchener, Ontario N2E 1W8
Kitchener, Ontario N2E 1W8
Phone
Hours
Mon–Fri 9 AM–5 PM • Sat 9 AM–1 PM
- Choosing a selection results in a full page refresh.
