GE Hotpoint Dishwasher Drain Pump WG04F11088 – Fix a Dishwasher That Won't Drain or Stops Mid-Cycle (Replaces WD19X24829)
GE Hotpoint Dishwasher Drain Pump WG04F11088 – Fix a Dishwasher That Won't Drain or Stops Mid-Cycle (Replaces WD19X24829)

GE Hotpoint Dishwasher Drain Pump WG04F11088 – Fix a Dishwasher That Won't Drain or Stops Mid-Cycle (Replaces WD19X24829)

Sale price
$183.91
Regular price
$200.46
You save
$16.55 (8%)

Frequently Bought Together

Confirm This Fits Your Model
Not sure where to find your model number? See guide →

What Customers Say About XPart Supply

4.82 ★ (250)
Verified
Genuine OEM Replacement Part

GE Hotpoint Dishwasher Drain Pump WG04F11088 – Fix a Dishwasher That Won’t Drain or Stops Mid-Cycle

OEM Part# WG04F11088 Replaces WD19X24829 Item #325 in Diagram Compatible: GE · Hotpoint · Electrolux

✓ Is This the Part You Need?

This is the genuine OEM drain pump for GE, Hotpoint, and Electrolux dishwashers. The drain pump is responsible for expelling water from the tub at the end of each wash and rinse cycle. When it fails, water sits in the bottom of the dishwasher, the cycle stalls, or the unit throws a drain error code. WG04F11088 directly supersedes WD19X24829 and is item #325 in the parts diagram.

✓ Symptoms This Fixes

  • Dishwasher not draining — standing water in the bottom of the tub after a cycle
  • Dishwasher stops mid-cycle and won’t continue
  • Drain error code displayed on the control panel
  • Dishwasher drains slowly or only partially
  • Loud humming, grinding, or buzzing noise during the drain phase
  • Dishwasher starts but water never pumps out

✓ Part Details

  • OEM Part Number: WG04F11088
  • Supersedes: WD19X24829
  • Diagram reference: Item #325
  • Genuine GE OEM — factory-specified fit and flow rate for compatible models
  • Controls water expulsion from the tub during wash, rinse, and drain cycles

✓ Installation Notes

  • Skill level: 2/5 — basic hand tools required
  • Estimated time: 30–45 minutes
  • ⚠ Disconnect power at the breaker before servicing
  • Turn off the water supply and have towels ready — residual water will be present in the sump
  • Access the drain pump by removing the lower spray arm, filter assembly, and sump cover
  • Disconnect the wire harness and drain hose before unclipping the pump from the sump housing
  • Confirm the new pump clicks fully into the sump housing before reassembling
  • Run a short cycle and check for leaks at the pump and drain hose connections before closing up

✓ Compatible Models

Compatible with GE, Hotpoint, and Electrolux dishwashers. Verify your full model number before ordering. Contact us to confirm compatibility.

GDT655SMJ5ES

Don’t see your model? Contact us — this part fits additional models not listed here.

💡 Pro Tip — Check the Filter and Drain Hose Before Replacing the Pump:
A clogged filter or kinked drain hose causes identical symptoms to a failed drain pump — standing water, mid-cycle stops, and drain error codes. Before ordering, remove and clean the filter assembly and inspect the drain hose for kinks or blockages at the garbage disposal or sink drain connection. If the pump runs (you can hear it hum) but water doesn’t move, the blockage is downstream. If the pump is silent during the drain phase, the pump motor has failed and WG04F11088 is your part.
WG04F11088 GE Hotpoint Dishwasher Drain Pump – Parts Diagram

✅Compatibility & Cross Reference

Item #325 in diagram

Part number WG04F11088 replaces WD19X24829

Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.

Buy Online Pick Up In-Store

Address
101 Trillium Dr
Kitchener, Ontario N2E 1W8
Phone
1-877-899-7278
Hours
Mon–Fri 9 AM–5 PM • Sat 9 AM–1 PM
Get Directions
Map showing warehouse location at 101 Trillium Dr, Kitchener
View on Google Maps