Menu
Whirlpool Washer Not Dispensing Detergent? Detergent Dispenser Housing W11158805 – Fix Soap Dispenser Failure Fast
A washer that doesn’t dispense detergent, fabric softener, or bleach properly is almost always a cracked, clogged, or broken detergent dispenser housing. In most Whirlpool front-load washers, the dispenser housing is the structural assembly that holds the detergent drawer and routes water through the correct compartments during the wash cycle. When it fails — through cracking, warping, or broken tabs — detergent dumps directly into the drum at the wrong time, softener never releases, or the drawer won’t seat properly. ⚡ Common failure point in Whirlpool and Maytag front-load washers. Part W11158805 is the genuine OEM replacement detergent dispenser housing that restores correct, timed detergent and softener dispensing. It supersedes and replaces the older part number W10432327.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ Washer powers on and runs cycles normally
- ✔ Water supply to the dispenser is confirmed — inlet valve and hoses are clear
- ✔ Dispenser drawer slides in and out but housing is cracked, broken, or leaking
- ✔ ONLY problem is detergent or softener not dispensing at the correct time
Not sure? Send us your model number — we’ll confirm before you order.
🔧 Common Symptoms
- Detergent left in drawer after cycle — soap not dispensing into drum
- Fabric softener not releasing during rinse cycle
- Bleach compartment not flushing correctly
- Dispenser drawer leaking water onto the floor or into the cabinet
- Drawer won’t seat or latch properly in the housing
- Visible cracks, broken tabs, or warping on the dispenser housing body
- Mold or residue buildup caused by water not flushing through correctly
✔ If these symptoms match, the detergent dispenser housing is the most likely failed component in the system.
✔ In most cases, replacing this housing restores correct detergent and softener dispensing immediately.
📦 Part Details
- Part Number: W11158805
- Type: Detergent Dispenser Housing Assembly
- Replaces / Supersedes: W10432327
- Brands: Whirlpool, Maytag, Amana, Kenmore (verify by model number)
✅ Updated Part: W11158805 is the current OEM part and directly supersedes W10432327. If you were searching for W10432327, this is the correct replacement to order.
⚠️ Recommended While Repairing:
While the dispenser housing is out, inspect the dispenser inlet valve and the water inlet hoses that feed the dispenser. A partially blocked inlet valve can cause the same symptoms as a failed housing — if water pressure to the dispenser is low, the new housing won’t fully resolve the issue. Clean or replace the inlet valve screen at the same time to ensure full water flow through the new housing.
While the dispenser housing is out, inspect the dispenser inlet valve and the water inlet hoses that feed the dispenser. A partially blocked inlet valve can cause the same symptoms as a failed housing — if water pressure to the dispenser is low, the new housing won’t fully resolve the issue. Clean or replace the inlet valve screen at the same time to ensure full water flow through the new housing.
⚙️ Installation
Skill Level: MODERATE — 30–45 minutes. Disconnect power before servicing. Open the washer door and remove the dispenser drawer, then unscrew the front panel or top panel (varies by model) to access the dispenser housing mounting screws. Disconnect the water inlet hoses from the housing, remove the mounting screws, and slide the old housing out. Install the new W11158805 housing, reconnect the inlet hoses, reassemble the panels, and run a rinse cycle to confirm correct dispensing.
✓ Compatible Models
Confirmed compatible with select Whirlpool and Maytag front-load washer models. Contact us to verify your model number before ordering.
💡 Pro Tip
Clean the Dispenser Cavity Before Installing the New Housing:
Before installing the replacement housing, thoroughly clean the dispenser cavity in the washer cabinet with a diluted white vinegar solution. Detergent and softener residue that built up around the old housing can block water flow through the new one and cause the same dispensing problems to return within a few months. A clean cavity ensures the new housing seats correctly and water routes through all compartments as designed.
Before installing the replacement housing, thoroughly clean the dispenser cavity in the washer cabinet with a diluted white vinegar solution. Detergent and softener residue that built up around the old housing can block water flow through the new one and cause the same dispensing problems to return within a few months. A clean cavity ensures the new housing seats correctly and water routes through all compartments as designed.
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Address
101 Trillium Dr
Kitchener, Ontario N2E 1W8
Kitchener, Ontario N2E 1W8
Phone
Hours
Mon–Fri 9 AM–5 PM • Sat 9 AM–1 PM
- Choosing a selection results in a full page refresh.
