Dishwasher Wobbling, Rocking, or Won’t Sit Level? Adjuster Kit W10712395 – Fix Leveling & Stability Fast

If your Whirlpool dishwasher rocks during wash cycles, won’t sit flush under the counter, or has a door that binds and won’t latch properly, a broken or worn adjuster leg is almost always the cause. In most Whirlpool, KitchenAid, and Kenmore dishwashers, the adjuster legs are the only point of contact between the unit and the floor — when one cracks or collapses, the entire appliance goes out of level. When it fails, the dishwasher shifts and bangs during operation, the door seal can gap and leak, and wash arms may spray unevenly due to the tilted tub angle. ⚡ Common failure point in Whirlpool-platform dishwashers pulled forward without releasing mounting screws first. Part W10712395 is the genuine OEM replacement kit that restores a stable, level installation and eliminates rocking, vibration, and door misalignment immediately.

❓ Is This the Right Part?

This is the correct fix if ALL of the following are true:

• ✔ Dishwasher powers on and runs wash cycles normally
• ✔ Door latch, spray arms, and pump all function correctly
• ✔ Water supply and drain confirmed OK — no plumbing issues
• ✔ ONLY problem is rocking, wobbling, uneven leveling, or door misalignment caused by a broken adjuster leg

Not sure? Send us your model number — we’ll confirm before you order.

🔧 Common Symptoms

• Dishwasher wobbles, rocks, or shifts during wash cycles
• Excessive banging or vibration noise during operation
• Dishwasher not sitting flush or level under the counter
• Door difficult to open, close, or latch properly
• Water leaking from the door due to improper leveling
• Visible broken, cracked, or missing adjuster leg
• Dishwasher tilts forward when door is opened

✔ If these symptoms match, the adjuster kit is the most likely failed component in the system.

✔ In most cases, replacing this adjuster kit restores a stable, level installation immediately.

📦 Part Details

• Part Number: W10712395
• Type: Dishwasher Adjuster Leg Kit — OEM Whirlpool / XPart Premium Alternative
• Replaces: W10250159, W10350375, W10712395VP
• Brands: Whirlpool, KitchenAid, Kenmore
• Kit Includes: Adjuster legs and all mounting hardware
• XPart SKU: W10712395CM  |  OEM SKU: W10712395

⚙️ Installation

Skill Level: Easy — 20 to 30 minutes. Disconnect power before servicing. Remove the lower access panel (2–4 screws) to access the adjuster legs. Loosen the existing legs with a wrench, slide out the old kit, install the new one, and adjust height until the dishwasher sits level and flush with the counter on all sides. Restore power and run a short cycle to confirm stability and check for door alignment.

✓ Compatible Models

Confirmed compatible with 66512762K312, 66512763K313, 66512769K313, 66512773K313, 66512773K314, WDT730PAHB0, WDT730PAHV0, WDT730PAHW0, WDT730PAHZ0, WDT750SAHB0, WDT750SAHV0, WDT750SAHW0, WDT750SAHZ0, WDT910SAYE0–SAYE3, WDT910SAYH0–SAYH3, WDT910SAYM0–SAYM3, WDT910SSYB0–SSYB3, WDT910SSYM0–SSYM3, WDT910SSYW0–SSYW3, WDT970SAHV0, WDT970SAHZ0, WDT975SAHV0, WDT975SAHZ0, WDTA50SAHN0, WDTA50SAHV0, WDTA50SAHZ0, WDTA75SAHN0, WDTA75SAHZ0, KDFE454CSS5, KUDC10FBBL0, KUDC10FBSS0, KUDC10FBWH0, KUDE20FBBL0, KUDE20FBBL1, KUDE20FBSS0, KUDE20FBSS1, KUDE20FBWH0, KUDE20FBWH1, plus additional Whirlpool, KitchenAid, and Kenmore models. Contact us to verify your model number before ordering.

💡 Pro Tip