Whirlpool Oven Not Heating or Showing Error Codes? Control Board W11261165 – Fix It Fast
A Whirlpool built-in wall oven that won’t heat, shows F or E error codes, has an unresponsive control panel, or shuts off mid-cycle is almost always caused by a failed electronic control board. In WOC, WOS, WOD, and WOEC series Whirlpool wall ovens, the control board is the central processor — it manages temperature regulation, bake and broil element cycling, display output, and all user inputs. When it fails, the oven may appear completely dead, throw persistent error codes, or power up but refuse to heat. ⚡ One of the most common high-value failures on Whirlpool built-in wall ovens, often triggered by power surges or thermal stress over time. Part W11261165 is the genuine OEM replacement that restores full oven control, heating, and display function immediately.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ The oven has power — display lights up or shows error codes
- ✔ The temperature sensor (RTD probe) has been tested and confirmed OK (~1,100Ω at room temp)
- ✔ Power supply at the breaker and outlet is confirmed OK
- ✔ ONLY problem is no heat, error codes that won’t clear, unresponsive controls, or mid-cycle shutoff
Not sure? Send us your model number — we'll confirm before you order.
🔧 Common Symptoms
- Oven won’t heat — bake or broil elements not cycling on
- Persistent F or E error codes on the display that won’t clear after a reset
- Control panel unresponsive — buttons not registering or display frozen
- Oven starts but shuts off mid-cycle unexpectedly
✔ If these symptoms match, this is the most likely failed component in the system.
✔ In most cases, replacing this control board restores full oven heating and control function immediately.
📦 Part Details
- Part Number: W11261165
- Type: Electronic Oven Control Board / Main PCB
- Replaces: W11040194, W11109171, W11253186
- Brands: Whirlpool
- Fits: WOC, WOS, WOD, WOEC, WOED, WOES, WOCA, WODA, WOSA series built-in wall ovens
Two cheaper parts mimic a failed control board. 1) Temperature sensor (RTD probe): A failed sensor causes no-heat and F3/E0 codes — test resistance at the sensor connector (should read ~1,100Ω at room temp). If open or shorted, replace the sensor first. 2) Relay board: Some WOC/WOD models use a separate relay board to switch bake and broil elements — if the display works but elements won’t cycle, the relay board may be the culprit. Confirm your model’s architecture before ordering the control board.
⚙️ Installation
Skill Level: ADVANCED — 30–45 minutes. Disconnect power at the breaker before servicing — control boards carry line voltage. Photograph all wiring harness connections before disconnecting. Access the control board through the display fascia or rear panel depending on model. Handle the board by its edges only to avoid static discharge. Reinstall in reverse order, restore power, and run a full bake cycle to confirm temperature accuracy before reassembling the fascia.
✓ Compatible Models
Confirmed compatible with WOC75EC0HS00, WOD77EC0HS00, WOS72EC7HS01, WOEC7030PZ00, WOCA7EC0HZ00 plus additional WOC, WOS, WOD, WOEC, WOED, WOES, WOCA, WODA, and WOSA series Whirlpool built-in wall oven models. Contact us to verify your model number before ordering.
💡 Pro Tip
Electronic control boards are extremely sensitive to electrostatic discharge (ESD). Always handle the new board by its edges, never touch the component side, and ideally use an anti-static wrist strap grounded to the oven chassis before installation. A board damaged by static during installation will fail immediately or intermittently — and won’t be covered under warranty. Take 30 seconds to ground yourself before touching the board.
✓ Model-Specific Repair Pages
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Kitchener, Ontario N2E 1W8
- Choosing a selection results in a full page refresh.
