Menu
Your Whirlpool Washer Won’t Start, Spin, or Agitate — WP8318084 Lid Switch Assembly Is the Fix
✓ Is This the Part You Need?
The WP8318084 is the lid switch assembly for Whirlpool, Maytag, Kenmore, and Roper top-load washers — the safety component that detects whether the lid is open or closed. When it fails, the washer won’t start, won’t spin, or won’t agitate even with the lid fully closed, because the control board never receives the signal to allow operation. Available as a Genuine OEM Whirlpool part or as our premium XPart aftermarket replacement at a lower price point. Replaces part numbers 8318084 and WP8318084VP.
⚠️ Check the Lid Strike Too: A worn or broken lid strike (the plastic tab the switch contacts) is often the real culprit before the switch itself fails. If the switch tests good, inspect the strike first — it’s a much cheaper fix. Ask our team to confirm the correct strike for your model.
✓ Common Symptoms Fixed
- Washer won’t start when lid is closed
- Washer won’t spin or agitate
- Washer stops mid-cycle unexpectedly
- No response when closing the lid
- Intermittent operation — works sometimes, not others
- Washer only works when lid is held down with pressure
✓ Part Details
- OEM Part Number: WP8318084
- Also Replaces: 8318084, WP8318084VP
- Appliance Type: Top-Load Washer
- Compatible Brands: Whirlpool, Maytag, Kenmore, Roper
- Component: Lid Switch Assembly — safety interlock, signals control board when lid is closed
- OEM Option: Genuine Whirlpool WP8318084 — meets original equipment specifications
- XPart Option: Premium aftermarket — same fit and function at a lower price point
- Used Options: Inspected pulls available for budget repairs or older machines — see variant selector
✓ Installation Notes
Skill Level: Easy–Moderate | Estimated Time: 15–30 minutes. Always unplug the washer before beginning any repair — never service while plugged in. The lid switch is typically accessed by removing the cabinet top or control panel depending on the model. Disconnect the wiring harness, remove the mounting screws, swap in the new switch, reconnect the harness, and reassemble. Test the lid strike condition before ordering — if the plastic tab is broken, replace the strike first as it’s a simpler and cheaper repair.
✓ Compatible Models
This lid switch assembly fits a wide range of Whirlpool, Maytag, Kenmore, and Roper top-load washers, including:
2DLSQ7533JQ3, 2DLSQ8000JQ3, 2DLXR7244MQ1, 3RGSC9455JQ3, 3RLBR8543JQ2, 3RLSQ8000JQ3, 3SLSR6233MQ0, 3XGSC9455JQ3, 3XLBR5432JQ2, 3XLBR8543JQ2, 3XLSQ7533JQ2, 6ALBR6245MW0, 6ALSC8255MW0, 6ALSQ8000MW0, 6ALSR7244MW0, 7MBP11973MQ1, 7MBPL9764MQ1, 7MLBR4121PQ0, 7MLBR5102MQ1, 7MLBR6103MT1, 7MLBR6103MT2, 7MLBR6103PQ0, 7MLBR6103PT0, 7MLBR7333MT1, 7MLBR7333MT2, 7MLBR7333PT0, 7MLBR8444MQ1, 7MLBR8444MQ2, 7MLBR8444MT1, 7MLBR8444MT2, 7MLBR8444PQ0, 7MLBR8444PT0, 7MLSC9545JQ6, 7MLSC9900PW0, 7MLSD8900PW0, 7MLSE7534PT0, 7MLSF7600PQ0, 7MLSF7600PT0, 7MLSQ8000JQ6, 7MLSQ8543JQ6, 7MLSQ8543JT6, 7MLSQ8545PQ0, 7MLSQ8545PT0, 7MLSQ8545PW0, 7MLSQ9549PQ0, 7MLSR5132JQ5, 7MLSR6232JQ5, 7MLSR6232JT5, 7MLSR6332KQ3, 7MLSR7103MQ1, and many more Whirlpool, Maytag, Kenmore, and Roper models.
Not sure if this fits your model? Contact us with your full model number and we’ll confirm before you order.
✓ Model-Specific Repair Pages
Don’t see your model? Contact us with your full model number and we’ll confirm fit before you order.
💡 Pro Tip — Test the Switch Before You Replace It:
Before ordering, confirm the lid switch is actually the failed component. Unplug the washer, access the switch, and test continuity across the terminals with a multimeter — a good switch shows continuity when the actuator is depressed, open circuit when released. Also inspect the lid strike (the plastic tab): if it’s broken or worn down, the switch never gets activated regardless of condition. Replacing the strike alone (a $5–10 part) can save you the cost of a full switch assembly.
Before ordering, confirm the lid switch is actually the failed component. Unplug the washer, access the switch, and test continuity across the terminals with a multimeter — a good switch shows continuity when the actuator is depressed, open circuit when released. Also inspect the lid strike (the plastic tab): if it’s broken or worn down, the switch never gets activated regardless of condition. Replacing the strike alone (a $5–10 part) can save you the cost of a full switch assembly.
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Address
101 Trillium Dr
Kitchener, Ontario N2E 1W8
Kitchener, Ontario N2E 1W8
Phone
Hours
Mon–Fri 9 AM–5 PM • Sat 9 AM–1 PM
- Choosing a selection results in a full page refresh.
