Menu
Washer Shaking Violently During Spin? Rear Strut Assembly WP22001988 – Fix Tub Vibration and Banging
If your Whirlpool, Maytag, or Kenmore top-load washer shakes excessively, bangs loudly, or walks across the floor during the spin cycle — a failed rear strut assembly is the most common structural cause. In most Whirlpool-platform top-load washers, this is caused by a worn or broken rear strut assembly. When it fails, the outer tub loses its rear suspension support — allowing it to swing freely during spin, causing violent vibration, loud banging, and potential damage to the cabinet and internal components. ⚡ Common failure point in Whirlpool, Maytag, and Kenmore top-load washers. Part WP22001988 is the genuine OEM rear strut assembly that restores proper tub suspension, absorbs spin-cycle forces, and eliminates excessive vibration and noise.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ Washer powers on and fills/drains normally
- ✔ Drum rotates and agitates correctly
- ✔ Leveling legs confirmed adjusted and floor is solid
- ✔ ONLY problem is excessive vibration, banging, or tub movement during spin cycle
Not sure? Send us your model number — we'll confirm before you order.
🔧 Common Symptoms
- Washer shaking or vibrating violently during spin cycle
- Loud banging or thumping noise during spin
- Washer walking or moving across the floor during operation
- Unbalanced load errors even with evenly distributed loads
- Visible tub movement or wobble during spin
- Rattling or clunking from the rear of the cabinet
✔ If these symptoms match, the rear strut assembly is the most likely failed suspension component.
✔ In most cases, replacing this strut assembly restores stable, quiet spin operation immediately.
📦 Part Details
- Part Number: WP22001988
- Type: Washer rear strut assembly — connects outer tub to cabinet frame, absorbs spin-cycle vibration
- Replaces: 22002083, 7404P008-60
- Brands: Whirlpool, Maytag, Kenmore (Whirlpool-platform top-load washers)
- Weight: 25 lbs
- Status: ⚠️ No Longer Available (NLA) — new OEM units are discontinued. Used units subject to availability.
⚠️ Recommended While Repairing:
While the cabinet is open, inspect the front suspension springs and snubber pad — both are common wear items on washers this age and are inexpensive to replace proactively. If the washer was vibrating for an extended period before the strut failed, the snubber pad is almost certainly worn flat. Replacing all suspension components at once ensures balanced tub support and prevents a repeat failure.
While the cabinet is open, inspect the front suspension springs and snubber pad — both are common wear items on washers this age and are inexpensive to replace proactively. If the washer was vibrating for an extended period before the strut failed, the snubber pad is almost certainly worn flat. Replacing all suspension components at once ensures balanced tub support and prevents a repeat failure.
⚙️ Installation
Skill Level: ADVANCED — 60–90 minutes. Professional installation recommended. Disconnect power before servicing. The rear strut assembly connects the outer tub to the rear cabinet frame — support the tub securely before removing the old strut to prevent it from dropping. Remove the rear access panel, disconnect the strut from both mounting points, and install the new assembly in reverse order. Torque all fasteners to spec per your service manual. Restore power and run a spin cycle to confirm stable operation.
✓ Compatible Models
Confirmed compatible with select Whirlpool, Maytag, and Kenmore top-load washer models. This part (WP22001988) superseded the earlier 22002083 strut assembly and was used across multiple Whirlpool-platform washer generations. Contact us to verify your model number before ordering.
💡 Pro Tip
Replace Struts in Pairs — Always:
Washers typically have two rear strut assemblies working together to support the tub. If one has failed, the other is under the same age and stress load and will likely fail soon after. Replacing both at the same time ensures balanced tub suspension, prevents a repeat repair, and saves the labour cost of a second disassembly. If a used unit is available for WP22001988, order two.
Washers typically have two rear strut assemblies working together to support the tub. If one has failed, the other is under the same age and stress load and will likely fail soon after. Replacing both at the same time ensures balanced tub suspension, prevents a repeat repair, and saves the labour cost of a second disassembly. If a used unit is available for WP22001988, order two.
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Address
101 Trillium Dr
Kitchener, Ontario N2E 1W8
Kitchener, Ontario N2E 1W8
Phone
Hours
Mon–Fri 9 AM–5 PM • Sat 9 AM–1 PM
- Choosing a selection results in a full page refresh.
