WP3976576 Dryer Timer Assembly

Sale price: $278.22
Regular price: $315.16
You save: $36.94 (12%)

Frequently Bought Together

Dryer Won’t Stop or Won’t Start? Timer Assembly WP3976576 – Fix Cycle Failures Fast

A dryer that runs continuously, won’t advance through its cycle, or stops before clothes are dry is almost always caused by a failed timer assembly. In most Kenmore and Whirlpool-platform dryers, the timer controls every phase of the drying cycle — heat, tumble, and cool-down. When it fails, the dryer may run non-stop, refuse to start, or cut off mid-cycle leaving clothes damp. ⚡ One of the most common electromechanical failures in Kenmore 110-series dryers. Part WP3976576 is the genuine OEM replacement that restores accurate cycle timing and full dryer operation.

❓ Is This the Right Part?

This is the correct fix if ALL of the following are true:

✔ Dryer powers on and drum tumbles normally
✔ Heating element and thermal fuse confirmed OK
✔ Electrical supply and door switch confirmed OK
✔ ONLY problem is the cycle not advancing, not stopping, or not starting on the timer setting

Not sure? Send us your model number — we’ll confirm before you order.

🔧 Common Symptoms

Dryer runs continuously and never shuts off automatically
Dryer won’t start when the timer knob is turned
Cycle stops early — clothes still damp after a full cycle
Timer knob turns freely but nothing happens

✔ If these symptoms match, this is the most likely failed component in the system.

✔ In most cases, replacing this timer assembly restores normal cycle operation immediately.

📦 Part Details

Part Number: WP3976576
Type: OEM Dryer Timer Assembly
Replaces: 3406015, 3406702, 3976576, 3976576R
Brands: Kenmore, Whirlpool

⚠️ Recommended While Repairing:
While the control panel is open, inspect the thermal fuse and cycling thermostat — these are inexpensive parts that commonly fail alongside the timer on older Kenmore dryers. Replacing them at the same time prevents a repeat service call if one of them is borderline.

⚙️ Installation

Skill Level: Moderate — 30–45 minutes. Disconnect power before servicing. Remove the control panel by releasing the clips or screws at the top of the dryer, disconnect the wiring harness from the old timer, transfer the knob to the new assembly, and reconnect. Reassemble the panel and run a timed cycle to confirm proper operation.

✓ Compatible Models

Confirmed compatible with Kenmore 11060802990, 11062802100, 11063012100, 11064832400, 11065922400, 11066812690, 11067622600, 11068622700, 11069622800, 11070802990, 11072802100, 11073012100, 11074832400, 11075922400, 11076812690, 11077622600, 11078622700, 11079622800, 110C70832990, and hundreds of additional Kenmore 110-series dryer models. Contact us to verify your model number before ordering.

💡 Pro Tip

Test the Timer Before You Replace It:
Set a multimeter to continuity mode and test across the timer terminals — a failed timer will show no continuity on circuits that should be closed. This confirms the timer is the fault before ordering. If you’re already pulling the control panel, also check the start switch: it’s a $10 part that fails silently and produces identical symptoms to a bad timer on these Kenmore models.

✓ Model-Specific Repair Pages

✅Compatibility & Cross Reference

Part number WP3976576 replaces 3406015, 3406702, 3976576, 3976576R

Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.

Buy Online Pick Up In-Store

Address

101 Trillium Dr
Kitchener, Ontario N2E 1W8

Phone

1-877-899-7278

Hours

Mon–Fri 9 AM–5 PM • Sat 9 AM–1 PM

Get Directions

Map showing warehouse location at 101 Trillium Dr, Kitchener

View on Google Maps

WP3976576 Dryer Timer Assembly

Frequently Bought Together

What Customers Say About XPart Supply