WATER LEAKING FROM THE WASHER OR POOR DRAINING CAUSED BY A DAMAGED, KINKED, OR OBSTRUCTED INNER DRAIN HOSE
Whirlpool Washer Drain Hose (inner) WPW10003250, Replaces W10003250, 8181740, Fixes Water leaking from the washer or poor draining caused by a damaged, kinked, or obstructed inner drain hose
Washing machine inner drain hose assembly connecting the drain pump to the back of the washer; used in front-load washers.
Part WPW10003250Replaces W10003250, 8181740Whirlpool
Washing machine inner drain hose assembly connecting the drain pump to the back of the washer; used in front-load washers.
Is This the Right Part?
Part NumberWPW10003250
ReplacesW10003250, 8181740
ManufacturerWhirlpool
Appliance TypeWasher
Part TypeDrain Hose (inner)
✅ Cross Reference Information
Current Part NumberWPW10003250
ReplacesW10003250, 8181740
Common Symptoms
- Washer leaves water in the tub or drains slowly
- Water leaks from the lower or rear area of the washer during draining
- Drain hose is visibly kinked, crushed, split, or disconnected
- Washer may produce a drain-related error when restricted water flow prevents proper draining
Check Before Replacing
- Unplug the washer and shut off its water supply before inspecting the hose.
- Visually inspect accessible portions of the inner drain hose and its connections for kinks, crushing, splits, loose connections, or signs of leakage.
- Check for standing water and place towels beneath hose connections before disconnecting anything, since residual water may be present.
- Confirm that the drain path is not blocked and that the hose is routed without sharp bends or pinching.
- After any repair, run a short drain or rinse test while observing the hose connections for leaks.
Pro Tip
A hose can be intact yet still contribute to poor draining if it is kinked or pinched; correct routing and unobstructed flow should be checked before replacing the part.
Part Details
Part NumberWPW10003250
Part TypeDrain Hose (inner)
ManufacturerWhirlpool
Appliance TypeWasher
Primary FunctionCarries wastewater from the washer drain pump through the rear of the washer for discharge to the household drain.
Cross ReferencesW10003250, 8181740
Key Features
- Whirlpool OEM inner drain hose assembly
- Designed for front-load washing machines
- Connects the drain pump to the rear discharge path
- Carries used water from the washer to the household drain
- Factory Certified Part; package contains one front-load washer drain hose
Installation Notes
- Disconnect electrical power and shut off the water supply before installation.
- Access and panel-removal requirements can vary by washer model; follow the model-specific service or installation instructions.
- When disconnecting the hose, use towels or a suitable container to catch residual water.
- Secure the replacement hose at both washer connections and route it so it is not kinked, crushed, or pinched.
- After installation, run a drain test and inspect all connections for leaks.
Verified Compatible Models
11043902202, 11044836300, 11044836301, 11045862404, 11045872404, 11045962403, 11045966403, GHW9100LQ0, GHW9100LQ1, GHW9100LQ2, GHW9100LW0, GHW9100LW1, GHW9100LW2, GHW9150PW0, GHW9150PW1
Fitment reminder: Match the complete appliance model number, including suffix or revision where applicable, before ordering.
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Address
101 Trillium Dr
Kitchener, Ontario N2E 1W8
Kitchener, Ontario N2E 1W8
Phone
Hours
Mon–Fri 9 AM–5 PM • Sat 9 AM–1 PM
- Choosing a selection results in a full page refresh.
