Washer Door Cracked or Broken? Door Glass WPW10388315 – Fix It Fast
A cracked or shattered front-load washer door glass is one of the most common reasons a washer is taken out of service. In most Whirlpool and Maytag front-load washers, the inner door glass can crack from impact, thermal stress, or a failed door seal that allows water to pool against the glass. When it fails, the washer won’t latch properly, may leak, or will refuse to start as a safety precaution. ⚡ Common failure point in Whirlpool-built front-load washers. Part WPW10388315 is the genuine OEM replacement door glass that restores a secure, leak-free seal and full washer operation immediately.
❓ Is This the Right Part?
This is the correct fix if ALL of the following are true:
- ✔ Your washer powers on and all controls function normally
- ✔ The door frame, hinge, and latch mechanism are intact and undamaged
- ✔ The door boot seal (bellow) is in good condition with no tears or mold
- ✔ Your model number is a Whirlpool, Maytag, Amana, or Kenmore front-load washer
- ✔ ONLY problem is cracked, chipped, or broken inner door glass
Not sure? Send us your model number — we’ll confirm before you order.
🔧 Common Symptoms
- Visible crack, chip, or complete break in the inner door glass
- Washer door will not latch or lock before starting a cycle
- Water leaking from the door area during wash or spin
- Washer displays a door lock error and refuses to start
- Error codes F5, E1, or door-lock fault codes on the display
- Sharp glass edges visible — safety hazard requiring immediate replacement
✔ If these symptoms match, this is the most likely failed component in the system.
✔ In most cases, replacing this door glass restores normal washer operation immediately.
📦 Part Details
- Part Number: WPW10388315
- Type: Front-Load Washer Inner Door Glass / Door Window
- Replaces: OEM direct-fit door glass — supersedes W10388315, W10261045, W10261046 (no modification required)
- Brands: Whirlpool, Maytag, Amana, Kenmore
While the door is disassembled, inspect the door boot seal (bellow) for tears, mold, or hardening — a damaged seal is a leading cause of door glass stress and cracking. Replacing both at the same time eliminates the root cause and prevents repeat glass failures.
⚙️ Installation
Skill Level: Moderate — 30–45 minutes. Disconnect power before beginning. Remove the door from the washer by unclipping the hinge pins, then separate the outer door panel from the inner frame using a trim tool to release the retaining clips around the perimeter. Lift out the broken glass, seat the new glass into the inner frame, and reassemble the door in reverse order. Ensure all clips are fully seated before rehanging the door — an improperly seated door can cause latch misalignment.
✓ Compatible Models
Confirmed compatible with select Whirlpool, Maytag, Amana, and Kenmore front-load washer models. Contact us to verify your model number before ordering.
💡 Pro Tip
Before separating the door panels, run a strip of painter’s tape around the seam to mark the original alignment. This makes reassembly faster and ensures the outer panel seats evenly — a misaligned door panel is the #1 cause of post-repair latch problems. Takes 30 seconds and saves 15 minutes of frustration.
See all parts, cross-references, and model compatibility: WPW10388315 Part Hub, W10388315, W10261045, W10261046
✓ Model-Specific Repair Pages
✅Compatibility & Cross Reference
Not sure about your model number? Call 1-877-899-7278 and we’ll help you confirm. All brand names are the property of their respective owners and are used for compatibility reference only.
Buy Online Pick Up In-Store
Kitchener, Ontario N2E 1W8
- Choosing a selection results in a full page refresh.
